Current Tools 282 Скачать руководство пользователя

Страница: 11 / 12

ASSEMBLY AND OPERATING INSTRUCTIONS

—

CONTINUED

OPERATING CART —

continued

F. Advance the hydraulic cylinder

and align the clevis with the

correct hole on the shoe for the

type conduit you will be bending

(Rigid/IMC or EMT). Insert the

clevis pin and secure with a spring

clip. Retract the hydraulic cylinder

and raise the shoe.

See Figure 11A.

G. Slide the follow bar to the start

position. See Figure 11B.

H. Disengage the caster brakes and roll the cart away from the bender.

NOTE: Swivel locks are provided on the front casters to help with maneuvering the cart.

I. Refer to your hydraulic bender manual to complete the set up for bending conduit.

J. After bending is complete, reverse this procedure to return the shoe and follow bar to the

Transfer Cart.

Figure 11A

Figure 11B

Содержание 282













Результаты поиска

Содержание 282

Отзывы:

Похожие инструкции для 282

Бренды по названию

Популярные бренды

Current Tools 282, Руководство по сборке, эксплуатации, безопасности и каталог запасных частей

Результаты поиска

Содержание 282

Отзывы:

Похожие инструкции для 282

Бренды по названию

Популярные бренды