Current Tools 282 Скачать руководство пользователя

Страница: 6 / 12

5. The gates on the roller bed are installed

at the factory. Ensure that all eight gates

(two per row) are in place and operable.

To open, lift the gate from the spring side

and rotate towards the front of the cart.

To secure, return the gate to the retainer

hole. (See Figure 6).

LOADING CART

NOTE: Engage the brake on all casters before loading or removing components

1. A set of pins (two per sides) are mounted under the roller bed to store the four saddles. Pull the

spring clips out of the mounting holes and slide the saddles onto the pins with the “u” of the

saddle under the roller bed. Replace the spring clips to secure the saddles. (See Figure 6A).

ASSEMBLY AND OPERATING INSTRUCTIONS

—

CONTINUED

Figure 6A

Figure 6

Gate

Spring

Side

Gate

Retainer

Hole

Содержание 282













Результаты поиска

Содержание 282

Отзывы:

Похожие инструкции для 282

Бренды по названию

Популярные бренды

Current Tools 282, Руководство по сборке, эксплуатации, безопасности и каталог запасных частей

Результаты поиска

Содержание 282

Отзывы:

Похожие инструкции для 282

Бренды по названию

Популярные бренды