background image

23

EXPERT WW   rev.12

EXPERT WW

2. If  the  tunnel  door  was  used  in  natural 
vent.:

a) If the tunnel door operates according to the 
room  temperature,  the  door fully opens  at  the 
start-up of tunnel ventilation and then goes the 
position associated with the 1

st

 tunnel stage; this 

allows  resetting the position of the actuator before 
entering in tunnel ventilation. 

b) If the tunnel door operates according to the 
static pressure, the tunnel door opens during 
the 

“Pre-Opening Time”

  and  then  starts  to  be 

controlled as a function of static pressure.
 

2. From Tunnel to Natural Vent.

1. If  the  tunnel  door  was  not  used  in  natural 
vent. :

When the controller re-enters in natural ventila-
tion [A], the natural ventilation curtain opens dur-
ing the 

“Continuous Open Delay”

 and the tunnel 

door fully closes. When this delay has elapsed, the 
natural curtain operates according to the natural 
ventilation timer [B].

2. If the tunnel door was used in natural vent. :

When the room temperature falls below the 
natural ventilation’s 

“Start Close at”

 tempera-

ture [A], the tunnel door and natural ventila-
tion curtain open during the 

“Continuous Open 

Delay”.

  When  this  delay  has  elapsed,  both 

outputs  operate  according  to  the  natural 
ventilation timer [B].

GRAPH 2

From tunnel to natural ventilation

Temperature falls

Natural ventilation

Tunnel ventilation

Natural Start 

Close at

6.3.2.  Transition Between Natural 
& Tunnel Vent.

1. From Natural to Tunnel Vent.

When the room temperature reaches the natural 
ventilation’s start temperature, the natural cur-
tain starts opening in timer mode [A] – if tunnel 
doors are used in natural ventilation, they open 
according to the same timer. When the room 
temperature reaches the start temperature of 
the first tunnel stage [C], the natural curtain 
stays still during the 

“Tunnel Close”

 delay and 

then  fully  closes.  Here’s  how  a  tunnel  door 
opens at the startup of tunnel ventilation: 

1. If  the  tunnel  door  was  not  used  in  natural 
vent.:

a) If the tunnel door operates according to the 
room temperature, the door reaches the posi-
tion associated with the 1

st

 tunnel stage when 

the controller enters in tunnel ventilation. The 
controller then starts the fans when the tunnel 
door reaches half the opening of that stage. 

b) If the tunnel door operates according to the 
static pressure, the tunnel door opens during 
the 

“Pre-Opening Time”

  and  then  starts  to  be 

controlled as a function of static pressure. The 
controller  starts  the  fans  when  half  of  the 

“Pre-Opening Time”

 has elapsed. 

GRAPH 1

From natural to tunnel ventilation

Temperature rises

Natural ventilation

Tunnel ventilation

1st tunnel

stage

(Open at)

(Close at)

6.3.3.  Natural Ventilation Settings

1. Select:

  Main menu 

  Start/Stop*
  Natural**
  Curtain #X

*  A password may be required to access this menu.
**  This menu is accessible if at least 1 natural ven-

tilation curtain is enabled in the Installation Setup 

(section 4.5).

Natural Curtain 1 Settings

 

Use   to navigate

Initial Open at 

80.0  °F

Start Close at 

78.0  °F

Start Open at 

82.0  °F

Initial Time 

20  sec

Open Time 

15  sec

Close Time 

15  sec

Off Time 

15  sec

Wind Delay 

10  sec

Tun.Close Dly 

300  sec

Continuous Open 

300  sec

Purge Move Time 

30  sec

2. Set the following parameters:

(Refer to previous sections to get further information 

on these parameters) 

Initial  Open  at  —

  Set  the  temperature  at 

which the curtain opens for the first time. The 
curtain opens during its initial moving time at 
that moment. 

Start Close at —

 Set the temperature below 

which the curtain starts closing in timer mode 
when the controller is in natural ventilation. 

Start Open at —

 Set the temperature above 

which the curtain opens according to a timer 
when the controller is in natural ventilation. 

Initial  Time  —

  The  curtain  opens  during 

its  initial  opening  time  when  the  controller 
enters  in  natural  ventilation.  This  opening 
time can be adjusted from 1 to 900 seconds 
(15 minutes).

Open /  Close / Off Time —

 Set the opening 

and  closing  timers  of  the  curtain  (the

 “Off 

Time” 

is common to both cycles). The open 

and close times range from 1 to 900 seconds 
(15 minutes); the

 “Off Time” 

ranges from 0 to 

900 seconds (15 minutes).

Содержание EXPERT WW
















































Отзывы: