manualshive.com logo in svg

Cubic Communications CDR-3250, Техническое руководство

Поделиться
Скачать
Cubic Communications CDR-3250 Скачать руководство пользователя страница 67

CDR-3250/80 TECHNICAL MANUAL

3-42

Issue 2.2

Utility - FAULTS Soft Key Menu.

8

9

CURNT

CUMUL

CANCEL

 MTR 

MNU

NEXT

The initial display shows the current fault status.  Press CUMUL to switch to display of cumulative faults since power was
turned on.  Press CURNT to switch back to display of current faults.  When pressed, the  

8

  

9

  keys allow scrolling through

multiple faults.  Up to 16 current (CURNT) or cumulative (CUMUL) faults may be displayed.  If the fault light is lit on the
vacuum fluorescent display, press the CURNT key to display the fault list.  The faults do not appear in any significant order
on the list.  To display the cumulative faults that have occurred since the receiver was turned on, press the CUMUL key.
Identical recurring faults will only appear once on the list.  Refer to paragraph 5-5.2.3 for details.

3-7.5.4

System. 

 This function allows selection of system related items including: software version identification, display

intensity, sound, and menu display default.

Utility Soft Key Menu.

TEST

CONFIG

FAULTS

SYSTEM

 MTR 

MNU

NEXT

Press SYSTEM to select system related items.  The following soft key menu appears.

Utility - SYSTEM Soft Key Menu.

ABOUT

INTENS

SOUND

MENUS

CANCEL

 MTR 

MNU

NEXT

Press the ABOUT key to display the receiver identification and software version number.  Press the NEXT key to show the DSP
firmware version number.  Press any soft key to return to the normal display.

Utility - SYSTEM Soft Key Menu.

ABOUT

INTENS

SOUND

MENUS

CANCEL

 MTR 

MNU

NEXT

Press the INTENS key to change the intensity of the front panel display.  The following soft key menu appears.

Courtesy of http://BlackRadios.terryo.org

Содержание CDR-3250





































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды