manualshive.com logo in svg

Cubic Communications CDR-3250, Техническое руководство

Поделиться
Скачать
Cubic Communications CDR-3250 Скачать руководство пользователя страница 48

CDR-3250/80 TECHNICAL MANUAL

Issue 2.2

3-23

.

Scan/Sweep - SCAN - NEXT Soft Key Menu.

RATE

SCAN

DONE

 MTR 

MNU

NEXT

Press the RATE key to change the scan rate, and the following menu appears.

Scan/Sweep - SCAN - NEXT - RATE Soft Key Menu.

BKSP

ENTER

RETURN

 MTR 

MNU

NEXT

Change the scan rate using the main adjustment knob and press the ENTER key.  The following menu appears.

Scan/Sweep - SCAN Soft Key Menu

FROM

TO

OFFSET

SCAN

DONE

 MTR 

MNU

NEXT

Press the SCAN key to start the scan.  The receiver will scan channels between the FROM and TO channels selected.  The
following menu appears.

Scan/Sweep - SCAN - SCAN Soft Key Menu.

STOP

CONT

SKIP

RETURN

 MTR 

MNU

NEXT

Press STOP to stop the scan, or CONT to continue the scan after stopping.  Press SKIP to skip a channel when dwelling or
bridging on that channel, and to set the skip flag for that channel.  That channel will be skipped during sweep or scan until the
skip flag is cleared.  Rotate the knob to change the scan rate during the scan if desired.

Courtesy of http://BlackRadios.terryo.org

Содержание CDR-3250





































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды