manualshive.com logo in svg

Cubic Communications CDR-3250, Техническое руководство

Поделиться
Скачать
Cubic Communications CDR-3250 Скачать руководство пользователя страница 20

CDR-3250/80 TECHNICAL MANUAL

Issue 2.2

2-3

GROUND

(GREEN)

NEUTRAL

(WHITE)

HOT

(BLACK)

Table 2-1  Rear Panel Connections.

Name

Connector

On Unit

Recommended

Mating Type

Description

POWER (J1)

IEC 320-C-13
(343-002)

NEMA 5-15P
(696-012, Power Cord)

90 to 260 VAC, 47 to 440 Hz, single phase 60 watts max. 
Figure 2-2 shows the pin descriptions.

REF IN (J2)

BNC  Jack
(344-246)

BNC Plug
(Customer Option)

Reference frequency in.  Used to connect 10 MHz external
frequency standard.   50 ohms, 0 dBm.

REF OUT (J3)

BNC  Jack
(344-246)

BNC Plug
(Customer Option)

Reference frequency out.  Used to connect to other receivers
or equipment using the same reference frequency standard. 
If external reference is used, this signal is the same as
applied to the REF IN connector.  50 ohms, 0 dBm.

SERIAL REMOTE
CONTROL (J4)
(Opt)

25-pin female D sub-
miniature connector. 

25-pin male D subminiature
connector. 
(Customer Option)

(Optional daughter board in Digital module, and cable
assembly must be installed). For external RS-232C or RS-
422 remote control bus operation.  Table 2-2 lists the pin
descriptions.  Refer to para 3-7.5.2.2.1 to set the serial bus
configuration.

IEEE-488 REMOTE
CONTROL (J4)
(Opt)

IEEE-488 24-pin
"blue ribbon"
connector assy. 

Standard IEEE-488 24-pin
connector. 
(Customer Option)

(Optional daughter board in Digital module, and cable
assembly must be installed).  For external remote control bus
operation.  Table 2-3 lists the pin descriptions.  Refer to para
3-7.5.2.2.2 to set the IEEE-488 bus address.  

ANTENNA (J5)

BNC Jack
(344-246)

BNC Plug
(Customer Option)

Coaxial antenna connection.  Impedance is approximately 50
ohms with a VSWR less than 3 to 1 at the receiver tuned
frequency.

NBIF (J6)

BNC  Jack
(344-246)

BNC Plug
(Customer Option)

Narrowband IF output signal.  Centered at 455 kHz with a
bandwidth equal to the selected bandwidth.  This output may
be connected to a spectrum analyzer or other equipment. 
The signal level is -10 dBm. 

DIGITAL DATA (J7)

15-pin "D"
subminiature male
(324-009)

15-pin "D" subminiature
female (324-070)

Used to connect I & Q outputs to external digital signal
processing equipment.    Table 2-4 lists the pin descriptions. 
Figure 2-3 shows the timing relationship.

AUDIO (J8)

15-pin "D"
subminiature female
(324-070)

15-pin "D" subminiature
male
(324-009)

Used to connect audio to optional RCU-3100 remote
controller or other equipment.  Table 2-5 lists the pin
descriptions.

WBIF (J9)

BNC  Jack
(344-246)

BNC Plug
(Customer Option)

Wideband IF (WBIF) output signal.  Centered at 456 kHz
(with a bandwidth of 30 kHz). This output may be connected
to a spectrum analyzer or other equipment.  For input signal
levels between 0 and -60 dBm, the WBIF signal level is -30
dBm.  For input signal levels below -60 dBm, the gain at the
WBIF output is approximately 30 dB.  

NOTE:  Part numbers in parenthesis (000-000) indicate CCI part number if applicable.

Figure 2-2  Power Connector (J1) Pin Descriptions.

Courtesy of http://BlackRadios.terryo.org

Содержание CDR-3250





































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды