manualshive.com logo in svg

Cubic Communications CDR-3250, Техническое руководство

Поделиться
Скачать
Cubic Communications CDR-3250 Скачать руководство пользователя страница 111

CDR-3250/80 TECHNICAL MANUAL

5-8

Issue 2.2

WARNING

CAUTION

CAUTION

5-6 SUBASSEMBLY REMOVAL AND
REPLACEMENT.

The following procedures describe removal and
replacement procedures for subassemblies that may be
removed and replaced at the operational level of
maintenance:

No internal adjustments (except audio line output and
internal reference adjustment) or component level
maintenance should be performed at the operational level.
These functions should  be performed at the factory or an
authorized repair depot.

Turn off power and remove power cord
before replacing subassemblies.  Personnel
injury or equipment damage may occur.

To remove the top or bottom cover, do the following: (Refer
to figure FO-5A (CDR-3250) or FO-5B (CDR-3280) for
locations.)

CDR-3250:  Using a no. 2 Phillips screwdriver, push down
and turn all captive fasteners on the cover 1/4 turn counter-
clockwise, and remove the cover. 

CDR-3280:  Using a no. 1 Phillips screwdriver, remove 4
screws from both sides of chassis for each cover to be
removed, and then remove the covers . 

In the following procedures, to prevent
damage to captive Allen screws or screw
holes in the chassis, ensure captive Allen
screws are completely retracted (but not
removed) from module before pulling
module from motherboard connector.

Module connectors may be difficult to
separate.  Pry gently on both sides of the
connector to assist module removal.

NOTE

When removing subassemblies, save
attaching hardware for subassembly
replacement. 

5-6.1

Synthesizer Module.

1.

Remove top cover.

2.

Using a 7/64 inch Allen wrench, loosen 8 Allen
screws from module.

3.

Pull module from motherboard connector.

4.

To replace, reverse removal procedures.

5-6.2

RF Analog Module.

1.

Remove top cover.

2.

Remove  Synthesizer module  per  paragraph 5-
6.1.

3.

Using a 7/64 Allen wrench, loosen 8 Allen
screws from module.

4

Disconnect WBIF coaxial cable.  

5.

Pull module from motherboard connector.

6.

To replace, reverse removal procedures.

7.

Replace  Synthesizer  module per  paragraph 5-
6.1.

5-6.3

Power Supply Module.

1.

Remove top and bottom cover.

2.

Using a no. 2 Phillips screwdriver, remove 4
screws and attaching hardware  from bottom of
module.

3.

Lift module from unit to disengage connector.

4.

To replace, reverse removal procedures.

5-6.4

AC Line Filter Board.

1.

Remove top and bottom cover.

2.

On CDR-3280 only, remove Power Supply
Module per paragraph 5-6.3 to reach AC Line
Filter board attaching screws.

3.

Using Phillips screwdriver, remove AC line
filter shield.

4.

Using Phillips screwdriver, remove 4 screws
from bottom of board.

5.

Disconnect all wires from board.

6.

Lift board from unit.

7.

To replace, reverse removal procedures.

5-6.5

Digital Module.

1.

Remove bottom cover.

2.

Using no. 1 Phillips screwdriver remove all
screws from module cover.

NOTE

The optional Remote Control
board is contained inside the
Digital module, and is  replaced as
a separate subassembly.

Courtesy of http://BlackRadios.terryo.org

Содержание CDR-3250





































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды