Crystal Vision TANDEM-200 Скачать руководство пользователя страница 107 | Manualshive

Страница: 107 / 141

background image

Crystal Vision

Installation

TANDEM-200 User Manual R1.7

106

13/02/2008

10 Installation

TANDEM-200 may be fitted into three of the Crystal Vision range of rackframes:

•

FR2AV 2U frame for up to 12 TANDEMs or other single height Crystal Vision
modules,

•

FR1AV 1U frame for up to 6 TANDEMs or other single height Crystal Vision
modules

•

DTB-AV 1U Desk top box for up to 2 TANDEMs or other single height Crystal
Vision modules.

There are five types of rear connector available to cater for all frames and to provide system
flexibility by allowing a mix between access to all connections and maximum module
packing density. Both balanced and unbalanced audio connectors are catered for.

RM04 RM07 RM36

12 TANDEMs in 2U, 6 in 1U
Analogue / 110

Ω

digital audio

No 2nd SDI output

6 TANDEMs in 2U 3 in 1U
75

Ω

digital audio

No 2nd SDI output

6 TANDEMs in 2U 3 in 1U
Analogue / 110

Ω

digital audio

2nd SDI output

RM05 RM08 RM36

9 TANDEMs in 2U
Analogue / 110

Ω

digital audio

2nd SDI output

9 TANDEMs in 2U
75

Ω

digital audio

No 2nd audio or SDI output

6 TANDEMs in 2U 3 in 1U
Analogue / 110

Ω

digital audio

2nd SDI output

The single-width rear connector achieves maximum card density with up to 12 TANDEM
cards in a FR2AV frame, albeit at the expense of losing the second buffered SDI outputs.
This solution also demands a high-density multiway connector for balanced digital audio
I/O, but all connections, including GPIs and analogue preview monitoring are available.

The loss of second SDI output can be avoided by using a taller rear module. A double-
height single card rear module allows access to all connections at six cards per 2U frame
and three cards per 1U frame. A special all-connection triple card rear module achieves
nine cards per 2U frame.

There are also double-height single-card and quad-height triple-card rear modules available
with BNCs for unbalanced

digital

audio. However, the double-height version does not have

the second SDI output and the triple does not have the second digital audio outputs. Triple
height modules only fit in the FR2AV 2U frame

«
...
105
106
107
108
109
...
»

Содержание TANDEM-200














































































































































Отзывы:

Нет отзывов

Похожие инструкции для TANDEM-200

Бренд: Barco Страницы: 100

Бренд: Omnia Страницы: 6

Бренд: YASKAWA Страницы: 34

RDX QuikStation 4

Бренд: Tandberg Data Страницы: 2

Бренд: IBM Страницы: 63

Бренд: XNET Страницы: 17

Бренд: Vivotek Страницы: 46

Бренд: Mod Страницы: 11

NetStructure ZT 5085

Бренд: Intel Страницы: 106

Бренд: HYCON Страницы: 13

Бренд: Baicells Страницы: 38

Бренд: Zmotion Страницы: 57

BioSense Series

Бренд: ZKTeco Страницы: 96

ControlWave Remote Ethernet I/O

Бренд: Emerson Страницы: 3

Бренд: Emerson Страницы: 6

Bristol Helicoid Gauges

Бренд: Emerson Страницы: 1

ACC/ARTM-7221/SCSI

Бренд: Emerson Страницы: 62

Бренд: Emerson Страницы: 106

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды