Crystal Vision TANDEM-200 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 141

background image

Crystal Vision

Installing Statesman

TANDEM-200 User Manual R1.7

23

13/02/2008

3.2 Selecting the operating mode

In general it is recommended to select the mode required just after an initial power up.
Once the selected mode is active, load 'total defaults' and assign other required settings
such as embedder and de-embedder audio groups - see section 9.3 in User Manual for
detailed operation.

The Mode tab works in the same way for all modes.

TANDEM-200 Mode tab

Select the required mode and then click on Confirm.

Wait until configuration has completed before attempting to use Statesman. The card-
edge display will show the configuration process from 0% in 5% steps up to 100%.

To change mode and have Statesman recognise the change proceed as follows:

•

change the TANDEM-200 mode as required from Statesman or the card-edge

•

Statesman will recognised its new mode once configuration completes

Mode changes to and from Mode 3

•

unplug TANDEM, remove all sub-PCB cards

•

re-power TANDEM and change mode using Statesman or card-edge controls

•

wait until configuration has completed then unplug TANDEM again

•

fit required sub-PCB cards to suit new mode

•

if necessary, delete old ‘instance’ from Statesman database as explained above

•

finally, load 'total defaults' and check audio group selection - see section 9.3 for
detailed operation

Note:

RS4 option cards are ONLY used for mode 3.
Mode 4 requires ‘B’ issue option cards.

«
...
22
23
24
25
26
...
»

Содержание TANDEM-200














































































































































Отзывы:

Нет отзывов

Похожие инструкции для TANDEM-200

Бренд: National Instruments Страницы: 28

Бренд: National Instruments Страницы: 19

Бренд: National Instruments Страницы: 103

NI PXI-1042 Series

Бренд: National Instruments Страницы: 12

Бренд: National Instruments Страницы: 4

Бренд: Commell Страницы: 9

OMB-DAQBOARD-3000 Series

Бренд: Omega Страницы: 108

Бренд: Altera Страницы: 93

NetVanta 6355 PoE

Бренд: ADTRAN Страницы: 46

RUGGEDMAX WIN7000

Бренд: RuggedCom Страницы: 42

Бренд: peplink Страницы: 2

Бренд: Accom Страницы: 15

EZ-Extender Analog 120-Pin Probing Board

Бренд: Analog Devices Страницы: 29

Seven Solutions WR-ZEN Series

Бренд: Orolia Страницы: 167

Бренд: Ubiquiti Страницы: 21

Бренд: SurfControl Страницы: 2

Бренд: Uniden Страницы: 5

Turbo NAS TVS-71 Series

Бренд: QNAP Страницы: 51

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды