Crystal Vision TANDEM-200 Скачать руководство пользователя страница 72 | Manualshive

Страница: 72 / 141

background image

Crystal Vision

The active control panel

TANDEM-200 User Manual R1.7

71

13/02/2008

Menu numbering scheme

This manual uses a simple menu numbering convention based on the sequence of keys
required to reach each menu from the top level home menu. For example, menu 1.1.2 is
reached from the home menu by pressing F1, then F2. Menu 1.1.2.1 is reached by
pressing F1, F2 and then F1 again.

Option codes

The following option codes are used in all TANDEM-200 control panel menus:

Menu code

Option code

Aip

AIP2

Aop

AOP2

Dip

DIP2

Rs2

DIP2RS

Rs4

RS4

Dop7

DOP2-75

Dop1

DOP2-110

Shorthand codes

The following shorthand codes are used in all TANDEM-100 control panel menus:

Menu code

Function description

SDI

Serial Digital Interface or serial component digital signal

SD

Side or ‘circuit’ of which there are two on each TANDEM-100 card

Mux1/Mux2

Embedder or multiplexer on side 1 or 2

Dmx1/Dmx2

De-embedder or demultiplexer on side 1 or 2

Out

Out 1 and Out 2 are used to refer to Demux outputs available to the
analogue monitor function when there is no output option-card

Opt

Generic term for option-card

OP

Generic term for option-card output

AG

Embedded audio group

D

Delay activated (per side)

/

Phase inversion

G

GPI

er

EDH errors above threshold detected

s

Audio signal silent (below –50dBs FS)

-

Signal not present

Note:

Take care not to confuse SDI with SD, or OP with Opt.

«
...
70
71
72
73
74
...
»

Содержание TANDEM-200














































































































































Отзывы:

Нет отзывов

Похожие инструкции для TANDEM-200

Бренд: Hama Страницы: 4

Бренд: Black Box Страницы: 9

Бренд: Direct IP Страницы: 76

Бренд: Waves Страницы: 41

Wisenet PRN-6400B4

Бренд: Hanwha Techwin Страницы: 14

Бренд: ZALMAN Страницы: 9

Бренд: Kanguru Страницы: 13

Бренд: SriHome Страницы: 12

Бренд: PairGain Страницы: 80

Бренд: M-system Страницы: 4

Бренд: IFM Страницы: 12

Бренд: Moxa Technologies Страницы: 8

Бренд: YASKAWA Страницы: 87

Бренд: Goobay Страницы: 28

Бренд: ICP DAS USA Страницы: 8

Бренд: National Instruments Страницы: 147

Бренд: AMD Страницы: 10

939GT2-Ultra Series

Бренд: JETWAY Страницы: 55

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды