Crystal Vision TANDEM-200 Скачать руководство пользователя страница 89 | Manualshive

Страница: 89 / 141

background image

Crystal Vision

Using card edge controls

TANDEM-200 User Manual R1.7

88

13/02/2008

Selecting sources and destinations

This menu, obtained with MENU DIL lever 4 ON (DOWN), is used to select the source
for each destination available on the board.

Available sources can be routed to embed destinations C and D with the embed routing.
De-embedded sources can be routed via output routing to option card destinations I or J
(if fitted).

The destination is selected using the SEL switch and the source is selected using the ADJ
shaft encoder. Save each source assignment by toggling MENU switch 1 down and then
up again.

SEL

No.

Display: available
sources

Source description
ADJ selects source

Display: valid

destination

Dest description
SEL selects dest

0 - 3

A1 - A4 (B1 - B4)
G1 - G4 (H1 - H4)

Varies according to
mode.

C1 - C4 Audio data embedded

into side 1 SDI stream.

4 - 7

(A1 - A4) B1 - B4
(G1- G4) H1 - H4

Varies according to
mode.

D1 - D4

Audio data embedded
into side 2 SDI stream.

8

–

B

A1 – A4

Data de-embedded from
SDI stream, side 1.

I1 - I4

Output option card
fitted to side 1

C - F

B1 – B4

Data de-embedded from
SDI stream, side 2.

J1 - J4

Output option card
fitted to side 2

Note:

The source and destination codes are the same as used in status displays.
Unavailable destinations are preceded by [no] in the display.
Rotation of the ADJ shaft encoder cycles through available sources and delay and phase
options – see next section for details.
Output option-card codes may be used even when no output option is present. This is
done to act as phantom destinations to allow the analogue monitoring output to select
routed (shuffled) de-embedded audio even though an output option-card is not
physically present.

Assigning delay/phase inversion and muting

When a source has been chosen for each destination during audio routing, it is possible to
set the audio processing options by turning the ADJ shaft encoder further. The available
options are delay, phase inversion, delay plus phase inversion, muting and normal.

Delay can only be associated with either the output routing or the embed routing on any
one side. It is not possible to assign delay in a path that involves output routing to external
audio outputs and to an embedder on the same side.

The delay function is assigned to the embedding path if the associated embedder is ON
("C" or "D"), or to the de-embedder output path if the associated embedder is OFF
(embedder "C” OFF selects delay for "A" de-embedder and embedder "D" OFF selects
delay for "B" de-embedder).

«
...
87
88
89
90
91
...
»

Содержание TANDEM-200














































































































































Отзывы:

Нет отзывов

Похожие инструкции для TANDEM-200

xStack Storage DSN-4000 Series

Бренд: D-Link Страницы: 5

Бренд: National Instruments Страницы: 85

SAFETank Series

Бренд: Raidon Страницы: 49

Бренд: Falcon Страницы: 24

Бренд: Uniden Страницы: 5

Бренд: IFM Electronic Страницы: 14

RADEON 9800 PRO

Бренд: ATI Technologies Страницы: 20

Бренд: B&B Electronics Страницы: 17

Бренд: Alesis Страницы: 11

Бренд: NXP Semiconductors Страницы: 1202

Бренд: ADTRAN Страницы: 136

Бренд: Matrix Switch Corporation Страницы: 48

Бренд: Zonet Страницы: 1

Бренд: Goobay Страницы: 28

Бренд: FabiaTech Страницы: 86

Бренд: Omnia Страницы: 130

System 200V PC 288

Бренд: VIPA Страницы: 54

Бренд: Tektronix Страницы: 143

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды