Assembly
NORTHBRIDGE WOOD ROOF
19950-100 Rev C (05-18)
© Copyright 2016, Creative Playthings
Page 5
FASTENERS
50559-700 Northbridge Hardware
77 12002-206 Flat Washer 5/16"
61 12017-206 Lock Washer 5/16"
61 17001-105 Weld Nut 5/16"
4 17003-1011 Hex Bolt 5/16 x 2-1/2"
13 17003-1211 Hex Bolt 5/16 x 3"
33 17003-1811 Hex Bolt 5/16 x 4-1/2"
8 17003-2411 Hex Bolt 5/16 x 6"
2 17036-1402 Lag Screw 5/16 x 3-1/2"
4 17036-1602 Lag Screw 5/16 x 4"
8 17036-1802 Lag Screw 5/16 x 4-1/2"
26 12002-207 Flat Washer 3/8"
17 12017-207 Lock Washer 3/8"
17 17001-103 Weld Nut 3/8"
13 17003-1813 Hex Bolt 3/8 x 4-1/2"
4 17003-2413 Hex Bolt 3/8 x 6"
4 17036-2203 Lag Screw 3/8 x 5-1/2"
4 17036-3203 Lag Screw 3/8 x 8"
152 17020-106 Screw #8 x 1-5/8"
50 17138-1025 T25 Screw #10 x 2-1/2"
16 17020-109 Screw #8 x 2-1/2"
11 17020-120 Screw #10 x 4-1/2"
13 17120-902 Self-Drilling Screw #10 x 2-1/2"
34 12002-203 Flat Washer 8mm
26 12017-205 Lock Washer 1/4"
28 17001-104 Weld Nut 1/4"
26 17003-609 Hex Bolt 1/4 x 1-1/2"
8 17036-601 Lag Screw 1/4 x 1-1/2"
2 17119-1209 Truss Head Bolt 1/4 x 3"
50559-900 Northbridge Roof Screws
130 17020-106 Screw #8 x 1-5/8"
CREATIVE PLAYTHINGS PLAY SETS USE A FEW STANDARD CONNECTIONS. BECOME FAMILIAR WITH
THESE CONNECTIONS TO EASE ASSEMBLY AND ENSURE A SAFER PLAY PRODUCT FOR YOUR CHILDREN.
Hex Bolt & Weld Nut Assembly Procedure:
Assembly Layout:
Align the holes in the parts to be fastened. Start
preliminary tightening of bolt into weld nut by
hand. Tighten each bolt with a wrench until the
lock washer is fully compressed between the
head of the bolt and the flat washer.
Correct Assembly:
Bolt has been screwed securely into weld nut
and the connection is tight. Check connec-
tions periodically for tightness during the life
of the Playset .
Do not over tighten.
Incorrect Assembly:
During assembly or maintenance the bolt pro-
trudes 1/8" past the weld nut. Call customer
service or replace the bolt at a local hardware
store. You may be overtightening or using the
wrong size bolt.
Failure to replace this bolt with a shorter
one could result in serious injury.
Typical Installation - Lag Screws:
• Pilot drill with the appropriate
diameter drill bit and then use
a socket to tighten.
• DO NOT over tighten
Typical Installation - Wood Screws:
• Use an electric drill or screw gun to drive screws.
• Drill 1/8" pilot holes where required.
• We recommend that you lubricate the
threads of the screws with beeswax or
soap to ease installation and minimize
breaking screws.
•
It is very important to make certain
that the tops of all screws are flush
with the surface of the wood and
there are no protruding sharp edges.
Lag Screw
Flat Washer
Hardware Bags
We have packaged more hardware than is required for
assembly.
