Crane Merchandising Systems BevMAX 4 Series Скачать руководство пользователя страница 38

Страница: 38 / 105

37 of 104

b. Plunger

Hits

Chassis.

i. Check tray is level and secured to tray supports.

ii. Check

harness

connections.

iii. Check X motor (bottom right).

iv. Check belt tension. Look for the belt to slip.

v. Check shelf adjust in DN Factory Diagnostics BevMax Setup Coke Factory Setup Set

Shelf Offset.

c. Plunger Stays Out.

i. Check for syrup or dirt build up.

ii. Check

Harness

connections.

iii. Replace cup assy.

3. Delivery Cup Assembly Will Not Go Home.

a. Is there a “Vend Mechanism” error on the display when the door has been opened?

i. If yes check the “Y” (lower) and “X” (top far left) home switches.

1. In Test Mode/ Test Vend with the top door switch (PI) pressed in:

a. At the home position the “Y” (lower) home switch will light a green LED on

the control board.

b. At the home position the “X” (top far left) home switch will light an amber

LED on the control board.

i. Adjust the X drive belt at the bottom left belt clamp.

4. Elevator will not move vertically.

a. Perform TEST MODE/TEST VEND to test movement.
b. Check left side door switch.

i. Is it functioning.

ii. Is it being made when door is closed.

c. Check the Delivery Cup Plunger & Plunger Home Switch.

i. If plunger arm is stuck out it will shut down XY delivery system.

ii. If plunger arm home switch fails it will shut down XY delivery system.

d. Check the 10 pin harness connector to the “Y” motor.
e. Check

rollers.

f.  Check Y motor harness and motor.
g.  Check E-Chain harness.
h.  Replace control board.

5. Elevator will not move horizontally.

a. Perform TEST MODE/TEST VEND to test movement.
b. Check left side door switch

i. Is it functioning.

ii. Is it being made when door is closed.

c. Check the lower and top far left home switches.

i. In Test Vend/Position Test with the left door switch (PI) pressed in:

1. At the home position the “Y” (lower) home switch will light a green LED on the

control board.

2. At the home position the “X” (top far left) home switch will light an amber LED on

the control board.

a. Adjust the X drive belt.

d. Check the Delivery Cup Plunger & Plunger Home Switch

i. If plunger arm is stuck out it will shut down XY delivery system.

ii. If plunger arm home switch fails it will shut down XY delivery system.

e. Check

rollers.

f. Check X motor harness and motor.
g. Replace control board.

Содержание BevMAX 4 Series










































































































Результаты поиска

Содержание BevMAX 4 Series

Отзывы:

Бренды по названию

Популярные бренды

Crane Merchandising Systems BevMAX 4 Series, Техническое руководство

Результаты поиска

Содержание BevMAX 4 Series

Отзывы:

Бренды по названию

Популярные бренды