31 of 104
Coke Factory Setup
Sold Out Enable- Should be “ON”
Press key 4 to enter menu, Use Vend Sensor, “ON”
or “OFF” will display. Press key 4 and the current
setting will flash. Press key 2 to change the setting.
Press key 4 to the setting will stop flashing and is
set. Press key “1” to exit menu.
Coke Factory Setup
$ Enable-
Press key 4 to enter menu. Use Dollar sign, “ON” or
“OFF” will display. Press key 4 and current setting
will flash. Press key 2 to change setting. Press key 1
to exit menu.
Coke Factory Setup
Enable EXE -
Use this menu to set the VMC for EXE peripheral
communication.
If the EXE is OFF, then the VMC
will communicate with MDB peripherals. (Note:
factory default is OFF. If the EXE is ON, then the
VMC will not communicate with MDB peripherals.
When the EXE is ON, additional configuration menus
will be made available in the standard setup menus
following Price Program. They include “Price Mode”,
“Price Program”, “View PL Assignments”, “View PL
Value” & “Quick Payback”. To enable EXE
communications: Press key 4 to select this menu.
You will see the current setting. Press key 4 to edit
the setting. You will see the current setting begin to
flash. Press key 2 to change the setting. Select “ON”
or “OFF.” Press key 4 to confirm the change. You
will see the current setting stop flashing. Press key 1
to exit menu.
Test Modes
Test Vend
–
Vend Testing
:
This function allows you to test vend each column.
Press key number 4 and the display will show
“Column A1”. Note: The left door switch must be
pulled to the out position to perform this test. Press
key numbers 2 or 3 to scroll through the columns
available to run in motor test. Press and hold the
Power Interrupt (PI) switch. Press key number 4 to
vend from the column displayed. Press key number 1
will return to “Test Vend”. Press key number 2 to scroll
to next test mode.
Test Sel Switch
–
Select Switch Test
:
This function allows you to test each selection.
Press key number 4 and the display will show
“Selection 4”. Then press any key and the display will
show the last key number pressed. Press and hold key
number 1 for approximately 5 seconds will return to
“Test Sel Switch”. Press key number 2 to scroll to the
next test mode.
Test Display
–
Display Test
:
This function allows you to test all segments in the
display. Press key number 4 and a row of lower
case letters “a” through “t” will display, then turn off,
then a row of upper case letters “A” through “T” will
display alternating until key number 1 has been
pressed. Press key number 1 to return to “Test
Display”. Press key number 2 to scroll to next test
mode.
Test Relays
–
Relay Test
:
This function allows you to test the relay electronic control
of the compressor (“Compressor #”), the evaporator
fan(s) (“Fan #”), and the sign front light (“Light#”).
CAUTION
: Disconnect power to the compressor before
testing the compressor relay. Failure to disconnect
power to the compressor before testing the relay could
result in damaging the compressor.
Press key number 4 and the display will show
“Compressor #”, where # is the state of the relay - 0
= not activated or off; 1 = activated or on. Press key
number 4 to toggle the relay on and off. Press key
number 2 to scroll to “Fan #”, where # is the state of
the relay - 0 = not activated or off, 1 = activated or
on. Press key number 4 to toggle the fan(s) on and
off. Press key number 2 to scroll
to “Light #”, where #
is the state of the relay - 0 = not activated or off; 1 =
activated or on. Press key
number 4 to toggle the
lights on and off. Press key number 1 to return to
“Test Modes”.
Press key number 2 to scroll to “Password Entry”.
Satellite (137/937) Setups
Satellite (137/937) Setup
Enable Snack Vender
–
Snack Vender Enable
on or off
:
This sub menu is used to enable and disable the
Snack Vender attached to the BevMax 4. 0 = off, 1 =
on. Press key number 4 and “#” will start flashing.
Press key number 2 or 3 to scroll between “Snack
Vender Enable 0” and “Snack Vender Enable 1”. Press
key number 4 with the display blinking the setting you
wish to use. Display will return to “Snack Vender”. To
set prices you must set vender for multiprice price
setting routine and return to Price Program.
Press key number 2 to scroll to next menu item.
Satellite (137/937) Setup
Golden-Eye Policy
–
Golden-Eye operating
condition
:
This sub menu is used to set the operating condition
of Golden-Eye. Note: Selections are
enabled/disabled in Set Golden-Eye Sel Mode.
Press key number 4 and the display will show the
Содержание BevMAX 4 Series
