background image

page 6

6. Wiring.

CAUTION

Be sure outlet box is properly grounded 

and that a ground wire (

GREEN

 or Bare) is present.

Make sure all electrical connections comply with 
Local Codes or Ordinances and the National 
Electrical Code. If you are unfamiliar with electrical 
wiring or if the house/building wires are different 
colors than those referred to below, please use a 
qualified electrician.

Note: 

Excess lead wire length from the fan can be 

cut to the desired length and then stripped.

When downrod is secured in place on the hanging 
bracket, electrical wiring can be made as follows:
Connect 

BLACK

 wire from fan to 

BLACK

 wire from 

ceiling with wire connector provided.
Connect 

WHITE

 wire from fan to 

WHITE

 wire from 

ceiling with wire connector provided.
Connect all 

GROUND 

(

GREEN

) wires together 

from fan to 

BARE

/

GREEN

 wire from ceiling with 

wire connector provided.

Since this fan does not come with a light kit, you 
will need to cap off the 

BLUE 

wire with a wire 

connector (as shown with arrow in diagram). 
[

Note

: If you elect to purchase a light kit for the 

fan, the 

BLUE

 wire from the fan must be 

connected to the 

BLACK

 (or 

RED

) wire from the 

ceiling instead.]

*Wrap each wire connector separately with 
electrical tape as an extra safety measure.

This fan is remote control adaptable (remote control 
sold separately). 

wire

connector

black

black

white

white

blue

black supply wire

white supply wire

from

ceiling

from fan

ground 
(green or bare)

*

ground 
(green 
or bare)

7. Canopy Assembly.

Locate 2 screws on underside of hanging bracket 
and remove screw closest to the open end of the 
hanging bracket. Partially loosen the other screw. 
Lift canopy to hanging bracket. Place rounded part 
of slotted hole in canopy over loosened screw in 
hanging bracket and push up. Twist canopy to lock. 
Re-insert screw that was previously removed and 
then tighten both screws securely.

Slide canopy cover up to canopy, aligning rounded 
part of slotted holes in canopy cover with screw 
heads in bottom of canopy. Turn canopy cover to 
the right (clockwise) until it stops.

canopy

screw

hanging bracket

screw

canopy cover

Содержание YOR52























Отзывы: