background image

page 5

5. Fan Assembly. (cont.)

hanging ball slot

motor housing

hanging bracket tab

safety cable

wood screw

and washer

safety cable

loop

wood
ceiling
joist

diagram 4

Thread safety cable and wires through hanging 
ball and then slide hanging ball over downrod--the 
top of the downrod should be noted as having a 
set screw hole; use this hole when setting the set 
screw. Insert stop pin into top of downrod and raise 
hanging ball. Be sure stop pin aligns with slots on 
the inside of the hanging ball. Tighten set screw 
securely. 

[

Refer to 

diagram 4

.

]

Remove electrical tape from electrical wiring and 
thread each of the wires through a different hole in 
the weatherproof hanging ball cover.  Pull 
weatherproof hanging ball cover down securely 
over hanging ball (on downrod). 
[

Refer to 

diagram 4

.

]

WARNING

: Failure to tighten set screw (on hanging 

ball) completely could result in the fan becoming 
loose and possibly falling.  

With the hanging bracket secured to the outlet box 
and able to support the fan, you are now ready to 
hang your fan. Grab the fan firmly with two hands. 
Slide downrod through opening in hanging bracket 
and let hanging ball rest on the hanging bracket. Turn 
the hanging ball slot until it lines up with the hanging 
bracket tab. [

Refer to 

diagram 5

.

]

WARNING

: Failure to align slot in hanging ball with 

tab in hanging bracket may result in serious injury or 
death.

Tip:

 Seek the help of another person to hold the 

stepladder in place and to help lift the fan up to you 
once you are set on the ladder.

Find a secure attachment point (wood ceiling joist 
highly recommended) and secure safety cable. It 
will be necessary to use a heavy duty wood screw, 
washer and lock washer (not supplied) with the 
safety cable loop. [

Refer to 

diagram 5

.

]

 
If necessary, adjust the loop at the end of the safety 
cable. The loop at the end of the safety cable 
should just fit over the threads on the wood screw. 

Test safety cable by pulling on loose end of cable with 
pliers. If the safety cable slips, the loop must be 
adjusted tighter. 

Extra cable slack can be left in 

ceiling area.

diagram 5

set screw hole

set screw

hanging ball

canopy

stop pin

safety cable

weatherproof 

hanging 

ball cover

electrical wiring

Содержание STK52

























Отзывы: