CorroVenta L4 Скачать руководство пользователя страница 31

Страница: 31 / 44

Description:

Manual L4 ES HP; L4 ES HP W

Document Number:

1004289

Created By:

MSHN

Revision Approval Date:

2019-06-28

Revision:

30 (42)

Alarms

If the machine detects a fault, corresponding information appears in a pop-up window. Additionally, a
warning symbol appears in the standard view's upper right corner, if one or more problems remain.

The following alarms can appear. Recommended corrective action is also given for each alarm.

Alarms

Action/advice

On or more slaves not responding

This alarm appears when the machine is used as

master in a network that has lost contact with one

or more of its slave machines. If this alarm appears,

check all system cables and the power supply to all

machines. When communication has been re-

established, the alarm disappears automatically

again.

Ambient temperature too high!

The machine has switched off all heaters due to too

high ambient temperature (above 35 degrees

Celsius). If continuous fan is selected, the fan

continues to run. The machine resumes operation

automatically if the temperature drops.

Fan control error

The fan speed deviates from the expected fan

speed. If the alarm remains, contact a service

technician.

No contact with internal control

board

Internal fault. If the alarm remains, contact a

service technician.

Internal sensor fault Temp and RH

sensor

Internal fault. If the alarm appears after the

machine has been disassembled, the fault may be

because the sensor connection to the cover has not

been installed correctly. If not, and if the alarm

remains, contact a service technician.

External Temp and RF sensor fault

The machine has lost contact with the external

temp and RH sensor(s). Check that the cables are

correctly installed. When contact with the external

Setpoint RH 60 %, start drying

Hysteresis
5 %

Stop drying = RH 55 %

Top

Содержание L4













































Результаты поиска

Содержание L4

Отзывы:

Бренды по названию

Популярные бренды

CorroVenta L4, Руководство пользователя

Результаты поиска

Содержание L4

Отзывы:

Бренды по названию

Популярные бренды