COP DAHUA DHI-VTH2421FW-P Скачать руководство пользователя страница 9

Страница: 9 / 16

ADDING AN ADDITIONAL VTO

In order to configure an additional VTO,

You must first follow the instructions on page 4.

1. Log into the

2nd VTO

and navigate to

Network Settings - SIP Server

, change from Enable to

Disable

and make sure

Server Type

is set to

VTO

2. Delete if present SIP Domain and username and password.

The IP address should be that of the main VTO and the default password of 123456

3. Now click

Save

The Device should now reboot and or request a reboot:

Reboot the VTO Now

Log back into the

Secondary VTO

and navigate to

Local Settings - Basic

change from

8001

8002

for the secondary. Click

Confirm

Main VTO

Secondary VTO

Note:

The VTO model shown in this diagram is only an example. Other VTO models can

also be added as secondary VTO’s.

Содержание DAHUA DHI-VTH2421FW-P

















Результаты поиска

Содержание DAHUA DHI-VTH2421FW-P

Отзывы:

Похожие инструкции для DAHUA DHI-VTH2421FW-P

Бренды по названию

Популярные бренды

COP DAHUA DHI-VTH2421FW-P, Инструкция по установке

Результаты поиска

Содержание DAHUA DHI-VTH2421FW-P

Отзывы:

Похожие инструкции для DAHUA DHI-VTH2421FW-P

Бренды по названию

Популярные бренды