COP DAHUA DHI-VTH2421FW-P Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 16

background image

6

Tel: +44 (0)1457 874 999 | Fax: +44 (0)1457 829 201 | Email: [email protected] | Online: www.cop-eu.com

The VTH Config menu is used to set the room number of the VTH and to configure the unit as a Master unit.

Tap VTH Config

Next, tap on SIP Server

The master monitor must have

#0

after the room

number - example:

1#0

Click OK

This is the VTO IP address

Network Port must match the SIP network port in

the VTO

Register Password is default 123456

Once logged into the VTH settings menu navigate to Network and configure the VTH Network settings to match that of the working

network and subnet of the VTO.

«
...
4
5
6
7
8
...
»

Содержание DAHUA DHI-VTH2421FW-P

















Отзывы:

Нет отзывов

Похожие инструкции для DAHUA DHI-VTH2421FW-P

BL-C30A - Wireless 802.11 b/g Network Camera

Бренд: Panasonic Страницы: 12

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 32

Бренд: Panasonic Страницы: 4

Бренд: Panasonic Страницы: 4

Бренд: Panasonic Страницы: 16

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 24

Бренд: Panasonic Страницы: 2

AWE300 - COLOR CAMERA

Бренд: Panasonic Страницы: 8

Бренд: Panasonic Страницы: 4

AKHC910 - 1080I CAMERA

Бренд: Panasonic Страницы: 14

AKHC3500 - MULTI FORMAT CAMERA

Бренд: Panasonic Страницы: 44

BB-HCM371A - Outdoor Wireless Network Camera

Бренд: Panasonic Страницы: 160

AWE860 - COLOR CAMERA

Бренд: Panasonic Страницы: 62

Бренд: Tamron Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды