Convotherm 10.10 mini страница 51 Скачать руководство пользователя

Страница: 51 / 75

6.5 Installing the ConvoClean System (for Units with ConvoClean /

Con)

6.5.1 Components of Fully Automatic Oven Cleaning System

Cleaning agents and rinse aid

Only use the products specified here in order to clean the combi oven.
NOTICE! The warranty will be void if there is any damage that can be traced back to the use of incor‐

rect cleaning agents.
The following table lists the cleaning agents and rinse aids that can be used:

Designation

Product

Label color

Cleaning agents

ConvoClean forte

Red

Rinse aid

ConvoCare

Green

Components and Configuration of Fully Automatic Oven Cleaning System with Connected Canisters

The figure below shows a size 6.10 mini combi oven used as an example representing all models:

No. Designation

Color coding

Unit connection for rinse aid

Green (inscription)

Unit connection for cleaning agent

Red (inscription)

Canister with ConvoCare rinse aid (ready-to-use solution with a de‐

fined mix ratio)

Green (label)

Suction tube with suction nozzle for rinse aid

Green (tube)

D10 wire hose clamp

Suction tube with suction nozzle for cleaning agent

Red (tube)

Canister with ConvoClean forte cleaning agent

Red (label)

Installation location for cleaning agent and rinse aid canisters

Set up the canisters as follows:

■

The canisters should be easily accessibly on a flat, level surface next to the device.

■

The canister's supporting surface must not be higher than the edge where the feet and the unit

case meet.

■

The canister's supporting surface must not be more than 40" below this edge.

6 Installation

Installation Manual

Содержание 10.10 mini












































































Результаты поиска

Содержание 10.10 mini

Отзывы:

Похожие инструкции для 10.10 mini

Бренды по названию

Популярные бренды

Convotherm 10.10 mini, Руководство по установке

Результаты поиска

Содержание 10.10 mini

Отзывы:

Похожие инструкции для 10.10 mini

Бренды по названию

Популярные бренды