Continuum Surelite EX 10 Скачать руководство пользователя страница 90

Страница: 90 / 114

Continuum Surelite Laser

996-0207

affect beam quality. This procedure instructs you on how to increase flashlamp pump voltage

to compensate for lamp aging.

ECESSARY

QUIPMENT

•

power meter

•

IR card

TEPS

1. Before increasing the pump voltage to bring the laser output back to spec energy, make

sure that your power decrease is not due to misalignment or optical damage.

2. Verify the energy specs by reviewing the Error! Reference source not found. on page

Error! Bookmark not defined. the front of the manual.

3. Position a power meter to monitor the IR energy. If the system has optional

harmonics, measure the total energy of the combined wavelengths. Due to losses in
the harmonic crystals, expect the measured combined total to be 15-20% below

published spec for IR alone.

4. Increase the pump voltage by 20 V on the PCU by the pressing the

SELECT

button

until red LED is lit next to

VOLT-AGE KV

on the front panel of the PCU.

5. Now use the

ARROW UP/ARROW DOWN

buttons as needed to reach +20 V.

6. Open the intra-cavity shutter. Allow the laser to Q-switch and measure the energy.

7. If still below specs, repeat steps 4 thru 6.

Note

If the total voltage increases exceed the installed voltage by more than

100 V, then the flashlamps should be replaced.

8. Check the free-running buffer. It needs to be at least 100 V. See

Eliminating free-

running

on page

9. If the energy is back to its spec level, log the date and action in “ Operator Notes” at

the end of the manual and the procedure is complete.

Cooling group contamination

This section describes the procedure for flushing the cooling group if it becomes
contaminated with organic material (algae).

ECESSARY

QUIPMENT

•

1 pint (~500 ml) 30% hydrogen peroxide

•

3 gal. distilled water

•

1 DI filter (PN#313-0099)

Содержание Surelite EX 10



















































































































Результаты поиска

Содержание Surelite EX 10

Отзывы:

Похожие инструкции для Surelite EX 10

Бренды по названию

Популярные бренды

Continuum Surelite EX 10, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Surelite EX 10

Отзывы:

Похожие инструкции для Surelite EX 10

Бренды по названию

Популярные бренды