Continuum Surelite EX 10 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 114

background image

Section 2: Installation

Installation requirements

The Surelite I & II laser systems are customer installed. The Surelite III & EX
laser systems are installed by Continuum personnel. The sections below give

detailed instructions regarding installation, tools necessary for installation and
equipment required to monitor laser performance. Read the Installation

section completely before beginning the installation. If you have any questions
or problems while performing the installation or to schedule an installation, call

Continuum Service at 1-877-272-7783.

Site

Install the laser in a closed and clean location. Your laser will work best in a

temperature stabilized environment. Therefore, it is advisable to set up the
system in an air conditioned room, placed so that no vents blow directly on the

laser and the laboratory temperature does not exceed 85°F (29.4°C). The laser
should be mounted on a solid work table that includes tapped 1/4-20 bolt holes

(or M6) at 1" centers so that the system can be secured to the table surface.

Choose a location for the power supply cabinet such that:

•

the back panel of the cabinet is not more than 10 feet (3.3m) away
from where the umbilical exits the laser.

•

the back panel of the cabinet is at least 2 feet (61cm) from a wall to
allow an unobstructed air flow to the cooling group.

•

each side of the cabinet is at least 8 inches (20 cm) away from the
wall or other obstacle to allow an unobstructed air flow to the
power supply.

Power

•

The voltage requirement is 200-240 V~, 50-60 Hz, single phase.

•

The amperage requirement is 10A.

Water

The water-to-air cooled heat exchanger requires no external cooling water

hook-up.

«
...
25
26
27
28
29
...
»

Содержание Surelite EX 10



















































































































Отзывы:

Нет отзывов

Похожие инструкции для Surelite EX 10

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 16

Бренд: DAKOTA ULTRASONICS Страницы: 48

Бренд: TE Connectivity Страницы: 9

Бренд: YATO Страницы: 36

Бренд: Dynojet Страницы: 88

Бренд: VP instruments Страницы: 15

Бренд: Fluidwell Страницы: 48

Бренд: Sensitech Страницы: 2

Бренд: az-instrument Страницы: 12

Бренд: NARDA Страницы: 14

DistanceMaster Compact

Бренд: LaserLiner Страницы: 14

Бренд: inbody Страницы: 36

Бренд: Stabila Страницы: 14

WJ-NX310K Series

Бренд: i-PRO Страницы: 18

Бренд: CWT Страницы: 41

Бренд: Bender Страницы: 4

Бренд: TEKELEK Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды