Continuum Surelite EX 10 Скачать руководство пользователя страница 56

Страница: 56 / 114

Continuum Surelite Laser

996-0207

3. Plug D connector made in step 2 to the

EXTERNAL

connector on front panel of the

PCU

4. Plug the Surelite into ac supply and toggle on the

AC POWER

5. Turn the keyswitch to the

position.

6. Press the

SELECT

button until

EoF

is displayed on the LED readout.

7. Press

UP ARROW

button so that display reads

Eon

8. Open exit port shutter at front of the laser bench.

9. Press the

START/STOP

button located of front panel of the

PCU

10. Press the

SHUTTER

button located of front panel of the

PCU

11. Input the Fire Command onto pin 7 of the D connector (TTL level 5 V

0 V, 10µs wide).

12. Input Q-switch Command onto pin 6 with a delay of ~180 µs with respect to Fire

Command (TTL level 5 V

0 V, 10 µs wide).

13. Adjust

T between Fire Command and Q-switch Command for maximum energy.

Note:

When running the system in the external mode you must flash the laser

head lamps at approximately the same frequency that the system was optimized at time
of purchase. Changing lamp frequency will change thermal lensing of the YAG rod

which can result in reduced system performance.

To disable DAT

1. Press the

START/STOP

button to stop lamps from flashing.

2. Press the

SELECT

button to

Eon

3. Press the

ARROW DOWN

button to

EoF

4. Resume normal operation.

Содержание Surelite EX 10



















































































































Результаты поиска

Содержание Surelite EX 10

Отзывы:

Похожие инструкции для Surelite EX 10

Бренды по названию

Популярные бренды

Continuum Surelite EX 10, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Surelite EX 10

Отзывы:

Похожие инструкции для Surelite EX 10

Бренды по названию

Популярные бренды