Contec IPC-BX/M560 Скачать руководство пользователя страница 24

Страница: 24 / 90

Hardware Setup

IPC-BX/M560(PCW)

Installing the Hard Disk Drive

(1) Connect the HDD cable bundled with the hard disk (silicon

disk) drive.

Note!

Connect the HDD cable with its connector justified to the left-hand

side of the connector on the back of the HDD. The four right-most

pins in the HDD connector are left unconnected, which are

master/slave setting pins. Use meticulous care when connecting the

HDD cable because turning the power on with the connector shifted

to the right may damage the HDD and/or the cable.

(2) Fasten the HDD onto the HDD bracket using four screws with

the cable passing through the slot in the HDD bracket.

• Use upper screw holes in the HDD bracket.
• Use either inner or outer screw holes in the HDD bracket,

depending on the type of the HDD you are installing. (The inner
screw holes are used in the example in Figure 3.4. below.)

(3) Connect the other end of the HDD cable to CN1 on the main unit

and mount the HDD bracket on the main unit using four screws.

(4) Close the top cover and tighten the screws.

Содержание IPC-BX/M560



























































































Результаты поиска

Содержание IPC-BX/M560

Отзывы:

Похожие инструкции для IPC-BX/M560

Бренды по названию

Популярные бренды

Contec IPC-BX/M560, Руководство пользователя

Результаты поиска

Содержание IPC-BX/M560

Отзывы:

Похожие инструкции для IPC-BX/M560

Бренды по названию

Популярные бренды