manualshive.com logo in svg

Comtrol InterChange VS 3000 Series, Руководство по установке и настройке

Поделиться
Скачать
Comtrol InterChange VS 3000 Series Скачать руководство пользователя страница 73

73

Error Codes and System Messages

CAPI3000 E302:

CAPI Connect Request: Virtual Server aaaaaaaa: Cannot 
allocate call entry!

A CAPI Connect Request from the specified application 
was rejected because all available call entries were active 
and in use.

CAPI3000 E303:

CAPI Connect B3 Request: Virtual Server aaaaaaaa: 
Invalid PLCI <0xhhhhhhhh>!

A CAPI Connect B3 Request was received from the 
specified application, but no call with the specified 
Physical Link Connection Identifier was in progress. 
Message discarded.

CAPI3000 E304:

CAPI Data B3 Request: Invalid data length dddd or 
address <0xjjjjjjjj>, NCCI <0xhhhhhhhh>!

A CAPI Connect B3 Request was received from the 
specified application, but the message at location jjjjjjjj 
with an NCCI of hhhhh was corrupted. Message ignored.

CAPI3000 E305:

CAPI Data B3 Request: Virtual Server aaaaaaaa/Port p/
Bn: No buffer available, NCCI <0xhhhhhhhh>!

A CAPI Data B3 Request was received for VS3000 
aaaaaaaa, port p, channel Bn, but no there were no 
available buffer headers. A queue full status was 
returned to CAPI.

CAPI3000 E306:

CAPI cmd_type: No call entry for PLCI <0xhhhhhhhh>!

A CAPI cmd_type was received but no active call entry 
could be found for the request's Physical Link Connection 
ID. Message discarded.

Valid cmd_types:

Disconnect Request
Connect Request
Connect Active Request
Disconnect Response

CAPI3000 E309:

CAPI Connect B3 Response: No call entry for NCCI 
<0xhhhhhhhh>, reject code <0xrr>!

A CAPI Connect B3 Response was received but no active 
call entry could be found for the request's Network 
Control Connection ID. Message discarded.

Table 6. CAPI3000 Error Codes

Code

Message and Description

Содержание InterChange VS 3000 Series



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды