manualshive.com logo in svg

Comtrol InterChange VS 3000 Series, Руководство по установке и настройке

Поделиться
Скачать
Comtrol InterChange VS 3000 Series Скачать руководство пользователя страница 69

69

Error Codes and System Messages

CAPI3000 E038: 

Error allocating ECB pool (nnnn bytes)!

Insufficient space for inbound ECB parking area of nnnn 
bytes. This pool is built on an application basis based on 
the number of outstanding packets per ISDN channel. 
Fatal.

CAPI3000 E100:

Unable to allocate transmit ECB, status <0xhhhhhhhh>, 
NIC dd!

No ECBs were available for issuing a transmit VS3000 
control request on NIC card dd. May need to use Novell 
system configuration utilities to allocate more ECBs. NIC 
driver may be holding on to ECBs too long.

If hhhhhhhh = FFFFFF89, either the packet size 
exceeded the maximum ECB size or an ECB was not 
available. No other statuses are defined.

CAPI3000 E101:

Unable to set Protocol ID, status <0xhhhhhhhh>, NIC dd!

The LSLGetPIDFromStackIDBoard system function 
returned an error code for NIC card dd while attempting 
to determine the stack ID before sending a VS3000 
control message. 

If hhhhhhhh = 0FFFFF82, either the protocol Stack ID or 
the board number does not exist.
If hhhhhhhh = 0FFFFF85, no Protocol ID is associated 
with the parameters passed. 
No other statuses are defined.

CAPI3000 E102:

Unable to transmit packet, status <0xhhhhhhh>, NIC dd!

Send of VS3000 control message to NIC card dd failed. If 
hhhhhhhh = 0FFFFF85, the NIC number dd is invalid. 
No other statuses are defined.

CAPI3000 E200:

Oversize (dddd) ASI command for Virtual Server 
aaaaaaaa!

An attempt was made to send a too-large ASI D-channel 
message to VS3000 unit aaaaaa. The size was dddd. The 
request was rejected. 

CAPI3000 E201:

Buffers unavailable for sending D channel data to Virtual 
Server aaaaaaaa/Port n!

Insufficient system buffers were available to issue a send 
request to the D-channel on VS3000 aaaaaaaa Port n. 
The request was rejected. 

Table 6. CAPI3000 Error Codes

Code

Message and Description

Содержание InterChange VS 3000 Series



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды