manualshive.com logo in svg

Comtrol InterChange VS 3000 Series, Руководство по установке и настройке

Поделиться
Скачать
Comtrol InterChange VS 3000 Series Скачать руководство пользователя страница 70

70

Error Codes and System Messages

CAPI3000 E202:

No ECBs available to send ASI packet to Virtual Server 
aaaaaaaa via NIC dd!

No ECBs were available to issue an ASI D-channel 
command to VS3000 aaaaaaaa attached to NIC card dd. 
The request was rejected. 

CAPI3000 E203:

Couldn't acquire Protocol ID from LSL, Virtual Server 
aaaaaaaa/NIC dd!

An attempt was made to send a D-channel message that 
was too large to VS3000 aaaaaaaa attached to NIC card 
dd. The request was rejected. 

CAPI3000 E204:

Send ASI packet failed to Virtual Server aaaaaaaa via 
NIC dd, status <0xhhhhhhhh>!

An ASI D-channel send request to VS3000 aaaaaaaa 
attached to NIC card dd was rejected. If hhhhhhhh = 
0FFFFF85, the NIC number dd is invalid. No other 
statuses are defined.

CAPI3000 E205:

Transmit complete, but no call entry match for Virtual 
Server aaaaaaaa/Port p/Bn!

An ASI B channel send request completed, but no call 
was active on VS3000 aaaaaaaa, port p, channel Bn. 
Request was rejected.

CAPI3000 E206:

Received Bn data lost, no call entry match for Virtual 
Server aaaaaaaa/Port p!

An ASI B channel message was received, but no call was 
active on VS3000 aaaaaaaa, port p, channel Bn. Message 
was discarded.

CAPI3000 E207:

Received Bn data lost from Virtual Server aaaaaaaa/Port 
p, application inactive!

An ASI B channel message was received on VS3000 
aaaaaaaa, port p, but no application was active and 
available for that message. Message was discarded.

CAPI3000 E208:

Received Bn data from Virtual Server aaaaaaaa/Port p 
lost, no ECB slots available for application dd!

An ASI B channel message was received on VS3000 
aaaaaaaa, port p, but the receive window on that 
particular port was closed. Message was discarded.

CAPI3000 E209:

Unidentified ASI command <0xhh> received from Virtual 
Server aaaaaaaa!

An apparent ASI message was received, but the type 
could not be identified. Message was discarded.

Table 6. CAPI3000 Error Codes

Code

Message and Description

Содержание InterChange VS 3000 Series



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды