Comtech EF Data CDM-740 Скачать руководство пользователя страница 69

Страница: 69 / 150

CDM-740 Advanced Satellite Modem

Revision 0

Front Panel Operation

MN-CDM740

5–17

Note the following:

Selection

Description

Auto

The port will auto-negotiate the configuration of the port (recommended
when the configuration of the port is unknown)

1000F

1000 Mb / Full Duplex

100F

100 Mb / Full Duplex

100H

100 Mb / Half Duplex

10F

10 Mb / Full Duplex

10H

10 Mb / Half Duplex

(CONFIG:) IP

(GE1 / GE2 / MGMT)

NegoSpeed

[HEADER] Negotiated Speed (read-only)
Down 1000F 100F 100H 10F 10H

(

◄►

Where [HEADER] is GE1, GE2, or MGMT( MANAGEMENT):

This is a ‘status only’ display

showing the negotiated line speed and duplex setting for this interface. Exit this

read-only

screen

by pressing

ENTER

CLEAR.

Note the following:

Selection

Description

Down

Ethernet is disconnected

1000F

1000 MB / Full Duplex

100F

100 MB / Full Duplex

100H

100 MB / Half Duplex

10F

10 MB / Full Duplex

10H

10 MB / Half Duplex

5.4.5.2 (CONFIG:) IP

(SNMP) Read-Cmty

SNMP Read Community (Max 15 chars)
[public ] (

◄►

To edit the SNMP Read Community string, use the

◄

►

arrow keys to select the character to edit,

then use the

▲

▼

arrow keys to select the desired character.

Note:

Only the first 15 characters on the bottom line are available.

All printable ASCII characters are available with the exception of the backslash (ASCII code 92)
and ~ (ASCII code 126).

Once the string has been composed, press

ENTER

. All trailing spaces are removed from the

Read Community string upon entry.

Содержание CDM-740























































































































































Результаты поиска

Содержание CDM-740

Отзывы:

Похожие инструкции для CDM-740

Бренды по названию

Популярные бренды

Comtech EF Data CDM-740, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CDM-740

Отзывы:

Похожие инструкции для CDM-740

Бренды по названию

Популярные бренды