background image

CDM-740 Advanced Satellite Modem  

Revision 0 

Preface 

MN-CDM740 

xvi 

The warranty does not cover any labor involved in the removal and or reinstallation of 
warranted equipment or parts on site, or any labor required to diagnose the necessity for 
repair or replacement. 

The warranty excludes any responsibility by Comtech EF Data Corporation for incidental or 
consequential damages arising from the use of the equipment or products, or for any inability 
to use them either separate from or in combination with any other equipment or products.

 

A fixed charge established for each product will be imposed for all equipment returned 
for warranty repair where Comtech EF Data Corporation cannot identify the cause of the 
reported failure. 

Exclusive Remedies 

Comtech EF Data Corporation’s warranty, as stated is in lieu of all other warranties, 
expressed, implied, or statutory, including those of merchantability and fitness for a 
particular purpose.  The buyer shall pass on to any purchaser, lessee, or other user of 
Comtech EF Data Corporation’s products, the aforementioned warranty, and shall 
indemnify and hold harmless Comtech EF Data Corporation from any claims or 
liability of such purchaser, lessee, or user based upon allegations that the buyer, its 
agents, or employees have made additional warranties or representations as to product 
preference or use. 

The remedies provided herein are the buyer’s sole and exclusive remedies.  Comtech EF 
Data shall not be liable for any direct, indirect, special, incidental, or consequential 
damages, whether based on contract, tort, or any other legal theory. 

Содержание CDM-740























































































































































Отзывы: