Comtech EF Data CDM-740 Скачать руководство пользователя страница 60

Страница: 60 / 150

CDM-740 Advanced Satellite Modem

Revision 0

Front Panel Operation

MN-CDM740

5–8

5.4.1.6 (CONFIG:) Tx

Data

Tx Data Rate: 9980.000 kbps
Tx Symbol Rate: 2851.429 ksps

(

◄►

To configure the

Tx Data Rate

(in kbps), on the top line select the digit of Data Rate to be edited

using the

◄

►

arrow keys, then change the value of that digit using the

▲

▼

arrow keys. Press

ENTER

when done.

The maximum limits for the Tx Data Rate are

16 kbps

9.98 Mbps

. The resolution is

1 bps

The actual minimum and maximum data rates are dependent on Framing mode, Interface type,
Modulation type and FEC Code Rate. If the user changes any of the higher-priority parameters –
causing the data rate to become invalid – the

Tx Data Rate

is adjusted automatically. The upper

range of data rate will also be dictated by the FAST option(s) installed.

To configure the

Tx Symbol Rate

(in ksps), on the bottom line select the digit of Symbol Rate to

be edited using the

◄

►

arrow keys. Change the value of that digit using the

▲

▼

arrow keys,

then press

ENTER

Refer to

Table 5-1

for Tx Symbol Rate and Data Rate ranges (TPC).

Table 5-1. Tx Symbol Rate / Data Rate Ranges – TPC

Modulation

FEC Code

Code Rate

Symbol Rate (Ksps)

Spectral

Efficiency

Data Rate (Kbps)

Min

Max

Min

Max

QPSK Turbo

21/44 16.762 2996.190 0.955 16.000 2860.000

3/4 10.667 3000.000 1.500 16.000 4500.000
7/8 9.143

3000.000

1.750

16.000

5250.000

0.95 8.421

2982.105

1.900 16.000

5666.000

8-QAM Turbo

3/4 7.111

3000.000

2.250

16.000

6750.000

7/8 6.095

3000.000

2.625

16.000

7875.000

0.95 5.614

2982.456

2.850 16.000

8500.000

16-QAM Turbo

3/4 5.333

3000.000

3.000

16.000

9000.000

7/8 4.800

2851.429

3.500

16.800

9980.000

5.4.1.7 (CONFIG:) Tx

Scrambler

Tx Scrambler: Off Normal IESS

(

◄►

Select

Off

Normal

, or

IESS

using the

◄

►

arrow keys, then press

ENTER.

Note the following:

•

When

Normal

is selected, the TPC scrambler is used.

•

When

IESS

is selected, the default ITU V.35 scrambler specified is used.

Содержание CDM-740























































































































































Результаты поиска

Содержание CDM-740

Отзывы:

Похожие инструкции для CDM-740

Бренды по названию

Популярные бренды

Comtech EF Data CDM-740, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CDM-740

Отзывы:

Похожие инструкции для CDM-740

Бренды по названию

Популярные бренды