Comtech EF Data CDM-740 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 150

background image

xi

PREFACE

About this Manual

This manual provides installation and operation information for the Comtech EF Data CDM-740
Advanced Satellite Modem. This is a technical document intended for earth station engineers,
technicians, and operators responsible for the operation and maintenance of the CDM-740.

Reporting Comments or Suggestions Concerning this Manual

Comments and suggestions regarding the content and design of this manual will be appreciated.
To submit comments, please contact the Comtech EF Data Technical Publications Department:

[email protected]

Conventions and References

Metric Conversion

Metric conversion information is located on the inside back cover of this manual. This information
is provided to assist the operator in cross-referencing non-Metric to Metric conversions.

Recommended Standard Designations

Recommended Standard (RS) Designations have been superseded by the new designation of the
Electronic Industries Association (EIA). References to the old designations are shown only when
depicting actual text displayed on the screen of the unit (RS-232, RS-485, etc.). All other references
in the manual will be shown with the EIA designations.

Trademarks

Product names mentioned in this manual may be trademarks or registered trademarks of their
respective companies and are hereby acknowledged.

«
...
15
16
17
18
19
...
»

Содержание CDM-740























































































































































Отзывы:

Нет отзывов

Похожие инструкции для CDM-740

Бренд: Elpro Technologies Страницы: 62

Бренд: ICP DAS USA Страницы: 21

Бренд: OUMAN Страницы: 4

Бренд: XtendLan Страницы: 54

Бренд: Sierra Wireless Страницы: 96

Бренд: NextNet Страницы: 26

Бренд: T-Home Страницы: 168

Merlin for GPRS G201

Бренд: Novatel Страницы: 54

Бренд: Spectrum Страницы: 8

Бренд: Four-Faith Страницы: 33

Бренд: U.S.Cellular Страницы: 59

COR IBR1100 series

Бренд: Cradlepoint Страницы: 5

Бренд: Cradlepoint Страницы: 20

Бренд: Flash Страницы: 2

Бренд: 3Com Страницы: 12

OnSite 1052 Series

Бренд: Patton electronics Страницы: 4

Бренд: Decmetrics Страницы: 2

Бренд: Paradise Datacom Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды