CompUSA 333628 Скачать руководство пользователя страница 12

Страница: 12 / 70

Chapter 2

General Settings

When you click the

General Setup

button at the Home Page, you will see the screen below.

The General Setup contains advanced features that allow you to configure the router to meet your network’s needs

such as: Wireless, Address Mapping, Virtual Server, Access Control, Hacker Attack Prevention, Special Applications,
DMZ, and other functions.

Below is a general description of each setting in General Setup.

Description

2.1 System

This section allows you to set the Broadband router’s system Time Zone, Password,
and Remote Management Settings.

2.2 WAN

This section allows you to select the connection method you need to establish a
connection with your ISP.

2.3 LAN

You can specify the LAN segment’s IP address, subnet Mask, enable/disable DHCP,
and select an IP range for your LAN.

2.4 Wireless

You can setup the wireless LAN’s SSID, WEP key, and MAC filtering.

2.5 QoS

You can setup the QoS bandwidth control policy.

2.6 NAT

You can configure the Address Mapping, Virtual Server, and Special Applications
functions in this section. This allows you to specify what user/packet can pass
through your router’s NAT.

2.7 Firewall

The Firewall section allows you to configure Access Control, Hacker Prevention, and
DMZ.

Select one of the above five General Setup selections and proceed to the relevant sub-section.

Содержание 333628







































































Результаты поиска

Содержание 333628

Отзывы:

Бренды по названию

Популярные бренды

CompUSA 333628, Руководство пользователя

Результаты поиска

Содержание 333628

Отзывы:

Бренды по названию

Популярные бренды