Comnet CNGE8MS Скачать руководство пользователя

Страница: 78 / 96

inS_cnge8MS_reV–

09/17/12 Page 78

INSTALLATION AND OPERATION MANUAL

CNGE8MS

Tech SupporT: 1.888.678.9427

Commands Set List—Port Commands Set

CNGE8MS

Commands

Level Description

Example

interface fastEthernet
[Portid]

Choose the port for modification.

switch(config)#interface
fastEthernet 2

duplex [full | half]

Use the duplex configuration command to
specify the duplex mode of operation for Fast
Ethernet.

switch(config)#interface
fastEthernet 2
switch(config-if)#duplex full

speed
[10|100|1000|auto]

Use the speed configuration command to
specify the speed mode of operation for Fast
Ethernet, the speed can’t be set to 1000 if the
port isn’t a giga port.

switch(config)#interface
fastEthernet 2
switch(config-if)#speed 100

flowcontrol mode
[Symmetric|
Asymmetric]

Use the flowcontrol configuration command
on Ethernet ports to control traffic rates
during congestion.

switch(config)#interface
fastEthernet 2
switch(config-if)#flowcontrol
mode Asymmetric

no flowcontrol

Disable flow control of interface

switch(config-if)#no
flowcontrol

security enable

Enable security of interface

switch(config)#interface
fastEthernet 2
switch(config-if)#security
enable

no security

Disable security of interface

switch(config)#interface
fastEthernet 2
switch(config-if)#no security

bandwidth type all

Set interface ingress limit frame type to
“accept all frame”

switch(config)#interface
fastEthernet 2
switch(config-if)#bandwidth
type all

bandwidth type
broadcast-multicast-
flooded-unicast

Set interface ingress limit frame type to
“accept broadcast, multicast, and flooded
unicast frame”

switch(config)#interface
fastEthernet 2
switch(config-if)#bandwidth
type broadcast-multicast-
flooded-unicast

bandwidth type
broadcast-multicast

Set interface ingress limit frame type to
“accept broadcast and multicast frame”

switch(config)#interface
fastEthernet 2
switch(config-if)#bandwidth
type broadcast-multicast

bandwidth type
broadcast-only

Set interface ingress limit frame type to “only
accept broadcast frame”

switch(config)#interface
fastEthernet 2
switch(config-if)#bandwidth
type broadcast-only

Содержание CNGE8MS

































































































Результаты поиска

Содержание CNGE8MS

Отзывы:

Похожие инструкции для CNGE8MS

Бренды по названию

Популярные бренды

Comnet CNGE8MS, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CNGE8MS

Отзывы:

Похожие инструкции для CNGE8MS

Бренды по названию

Популярные бренды