manualshive.com logo in svg

Comnet CNGE8MS, Инструкция по установке и эксплуатации

Поделиться
Скачать
Comnet CNGE8MS Скачать руководство пользователя страница 61

inS_cnge8MS_reV–

09/17/12     Page 61

INSTALLATION AND OPERATION MANUAL 

CNGE8MS

Tech SupporT: 1.888.678.9427

802.1x-Port Authorized State

802.1x Port Authorize State interface

Warning

The Warning function is very important for switch management. You can manage the switch by 
SYSLOG, E-MAIL, and Fault Relay. It helps monitor the switch status on a remote site. When events 
occur, the warning message will be sent to your appointed server, E-MAIL, or relay fault to the 
switch panel.

Fault Alarm 

When any selected fault event has occurred, the fault LED in the switch panel will illuminate and 
the electric relay will signal at the same time. 

Fault Alarm interface

The following table describes the labels in this screen.

Label

Description

Power Failure

Mark the blank of PWR 1 or PWR 2 to monitor.

Port Link Down/
Broken

Mark the blank of port 1 to port 8 to monitor.

Apply

Select “Apply” to set the configurations.

Help

Show help file.

Содержание CNGE8MS

































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды