manualshive.com logo in svg

Comnet CNGE8MS, Инструкция по установке и эксплуатации

Поделиться
Скачать
Comnet CNGE8MS Скачать руководство пользователя страница 33

inS_cnge8MS_reV–

09/17/12     Page 33

INSTALLATION AND OPERATION MANUAL 

CNGE8MS

Tech SupporT: 1.888.678.9427

Port Configuration

Port Control

By this function, you can set the state, speed/duplex, flow control, and security of the port.

Port Control interface

The following table describes the labels in this screen.

Label

Description

Port NO.

Port number for setting.

Speed/Duplex

You can set Auto-negotiation; 100 full,100 half,10 full,10 half mode.

Flow Control

Support symmetric and asymmetric mode to avoid packet loss when 
congestion occurred. 

Security

Support port security function. When enabled, the port will STOP 
learning MAC address dynamically.

Apply

Select 

Apply

 to set the configurations.

Port Status

The following information provides the current port status information

Port Status interface

Содержание CNGE8MS

































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды