CommScope e-POI Скачать руководство пользователя страница 59

Страница: 59 / 86

M0201ABK_uc

ERA® WCS and e-POI Subracks and Power Supply Unit Installation Guide

© June 2021 CommScope, Inc.

Page 59

Install and Connect the Subrack Cards

If the signal levels of the BTS exceed the maximum input level of + 16 dBm, an e-POI Module or other

suitable attenuator must be used to attenuate the signal. For optimum PIM performance, the composite

level into a Donor (RFD Card) port should be less than 16 dBm. If only one carrier is in a band, PIM is

probably not a concern. For the case of two or more carriers in a band, spurious intermods due to PIM

could land in the UL causing interference. Whether or not PIM will cause interference depends on the

spacing between UL and DL and the frequencies of active carriers.

NOTE:

This graphic shows a current RFD Card. Older RFD Cards (PN 7633229-00, PN 7633229-01)

have an LCD window and DISPLAY buon.

LTE 2x2 MIMO (AP0 or AP1)

to/from

BTS/eNodeB or e-POI

LTE 2x2 MIMO (AP0 or AP1)

to/from

BTS/eNodeB or e-POI

Ports set to Simplex

LTE MIMO 4x4 All Paths (AP0, AP1, AP2, AP3)

to/from

BTS/eNodeB or e-POI

Ports set to Duplex

LTE MIMO 2x2 (AP0, AP1)

to/from

BTS/eNodeB or e-POI

Ports set to Duplex

LTE MIMO 2x2 (AP0, AP1)

to/from

BTS/eNodeB or e-POI

Содержание e-POI























































































Результаты поиска

Содержание e-POI

Отзывы:

Бренды по названию

Популярные бренды

CommScope e-POI, Руководство по установке

Результаты поиска

Содержание e-POI

Отзывы:

Бренды по названию

Популярные бренды