CommScope e-POI Скачать руководство пользователя страница 19

Страница: 19 / 86

M0201ABK_uc

ERA® WCS and e-POI Subracks and Power Supply Unit Installation Guide

© June 2021 CommScope, Inc.

Page 19

WCS-2 and WCS-4 Subrack Overview

Slot and Card Assignment Rules for Switching CANs

Figure 3

lists the card installation rules for a WCS-4 or WCS-2 Subrack configured in the GUI to function as a

Switching CAN, in which case the CAN

will

be connected to a WIN.

Figure 3.

Supported Slot and Card Installations for Switching CANs

The following additional rules apply to a Switching CAN.

•

You cannot directly connect APs to a Switching CAN; connect the APs to a TEN that then connects to the

Switching CAN.

•

You cannot install a CAT, AUT, RFD, or CDD Card in a Switching CAN.

Card Slot

Supported Card Type

L1 - L8

Install an OPT Card to connect to a TEN.

M1 - M2

Not supported/used.

Install a SUI Card for network connectivity.

R1 - R8

Install an OPT Card to connect to a WIN.

For information on how to configure the WCS Subrack as a Switching CAN in the ERA software, refer to

the ERA configuration guide for Software Version 2.5 or later; see

"Accessing ERA Series User

Documentation” on page 83

Port

Slot

KEY:

WCS-2 Chassis conﬁgured as a Switching CAN

WCS-4 Chassis conﬁgured as a Switching CAN

Содержание e-POI























































































Результаты поиска

Содержание e-POI

Отзывы:

Бренды по названию

Популярные бренды

CommScope e-POI, Руководство по установке

Результаты поиска

Содержание e-POI

Отзывы:

Бренды по названию

Популярные бренды