CommScope e-POI Скачать руководство пользователя страница 46

Страница: 46 / 86

ERA® WCS and e-POI Subracks and Power Supply Unit Installation Guide

M0201ABK_uc

Page 46

© June 2021 CommScope, Inc.

Safely Working with ERA Hardware

L'antenne (s) utilisé pour cet émetteur doit être installé pour fournir une distance de séparation d'au

moins 100 cm de toutes les personnes et ne doit pas être co-localisées ou opérant en conjonction avec une

autre antenne ou émetteur. Les utilisateurs et les installateurs doivent être fournis avec des instructions

d'installation de l'antenne et des conditions de fonctionnement de l'émetteur pour satisfaire la

conformité aux expositions RF.

Notice:

The unit complies with Overvoltage Category II. It also complies with the surge requirement

according to EN 61000-4-5 (fine protection); however, installation of an additional medium (via local

supply connection) and/or coarse protection (external surge protection) is recommended depending on

the individual application in order to avoid damage caused by overcurrent.
For Canada and US, components used to reduce the Overvoltage Category shall comply with the

requirements of IEC 61643-series. As an alternative, components used to reduce the Overvoltage

Category may comply with ANSI/IEEE C62.11, CSA Certification Notice No. 516, CSA C22.2 No. 1, or UL

1449. Suitability of the component for the application shall be determined for the intended installation.

Notice:

Corresponding local particularities and regulations must be observed. For national deviations,

please refer to the respective documents included in the manual CD that is delivered with the unit.

For a Class B digital device or peripheral:

Note:

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in

a particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

•

Consult the dealer or an experienced radio/TV technician for help

Notice:

For a Class A digital device or peripheral.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

Note:

This unit complies with European standard EN60950-1 / EN62368-1.

Содержание e-POI























































































Результаты поиска

Содержание e-POI

Отзывы:

Бренды по названию

Популярные бренды

CommScope e-POI, Руководство по установке

Результаты поиска

Содержание e-POI

Отзывы:

Бренды по названию

Популярные бренды