manualshive.com logo in svg

CommScope e-POI, Руководство по установке

Поделиться
Скачать
CommScope e-POI Скачать руководство пользователя страница 45

M0201ABK_uc

ERA® WCS and e-POI Subracks and Power Supply Unit Installation Guide 

© June 2021 CommScope, Inc.

Page 45

Safely Working with ERA Hardware

2

Notice:

 For installations which have to comply with European EN50385 exposure compliance 

requirements, the following Power Density limits/guidelines (mW/cm²) according to ICNIRP are valid:

•

0.2 for frequencies from 10 MHz to 400 MHz

•

F (MHz) / 2000 for frequencies from 400 MHz to 2 GHz

•

1 for frequencies from 2 GHz to 300 GHz

3

Notice:

 Installation of this equipment is in full responsibility of the installer, who has also the 

responsibility, that cables and couplers are calculated into the maximum gain of the antennas, so that this 

value, which is filed in the FCC Grant and can be requested from the FCC data base, is not exceeded. The 

industrial boosters are shipped only as a naked booster without any installation devices or antennas as it 

needs for professional installation.

4

Notice:

 For installations which have to comply with FCC/ISED requirements:

English:

 

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 

(1) This device may not cause harmful interference, and (2) this device must accept any interference 

received, including interference that may cause undesired operation. 
This device complies with Health Canada's Safety Code. The installer of this device should ensure that RF 

radiation is not emitted in excess of the Health Canada's requirement. Information can be obtained at 

http://www.hc-sc.gc.ca/ewh-semt/pubs/radiation/radio_guide-lignes_direct-eng.php

.

Changes or modifications not expressly approved by the party responsible for compliance could void the 

user's authority to operate the equipment.

Antenna

 

Stmt

 

for

 

ISED:

 

This device has been designated to operate with the antennas having a maximum gain of 9 dBi. Antennas 

having a gain greater than 9 dBi are prohibited for use with this device without consent by ISED 

regulators. The required antenna impedance is 50 ohms.
The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 100 

cm from all persons and must not be co-located or operating in conjunction with any other antenna or 

transmitter. Users and installers must be provided with antenna installation instructions and transmitter 

operating conditions for satisfying RF exposure compliance.

French:

 

Cet appareil est conforme à partie15 de FCC des règles Partie15. Son utilisation est soumise à Les deux 

conditions suivantes: (1) cet appareil ne peut pas provoquer d'interférences et (2) cet appareil doit 

accepter Toute interférence, y compris les interférences qui peuvent causer un mauvais fonctionnement 

du dispositif.
Cet appareil est conforme avec Santé Canada Code de sécurité 6. Le programme d'installation de cet 

appareil doit s'assurer que les rayonnements RF n'est pas émis au-delà de I'exigence de Santé Canada. Les 

informations peuvent être obtenues: 

http://www.hc-sc.gc.ca/ewh-semt/pubs/radiation/radio_guide-lignes_direct-eng.php

 

Les changements ou modifications non expressément approuvés par la partie responsable de la 

conformité pourraient annuler l'autorité de l'utilisateur à utiliser cet équipement.

Antenne

 

Stmt

 

pour

 

ISDE:

 

Ce dispositif a été désigné pour fonctionner avec les antennes ayant un gain maximal de 9 dBi. Antennes 

ayant un gain plus grand que 9 dBi sont interdites pour une utilisation avec cet appareil sans le 

consentement des organismes de réglementation d'ISDE. L'impédance d'antenne requise est 50 ohms.

Содержание e-POI























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды