manualshive.com logo in svg

CommScope e-POI, Руководство по установке

Поделиться
Скачать
CommScope e-POI Скачать руководство пользователя страница 4

ERA® WCS and e-POI Subracks and Power Supply Unit Installation Guide

M0201ABK_uc 

Page iv

© June 2021 CommScope, Inc.

 Table of Contents

 

Minimum Optical Path Loss .............................................................................................................................................................................. 60

Maximum Optical Path Loss.............................................................................................................................................................................. 60

Optical Link Loss................................................................................................................................................................................................ 61

Minimum Performance Levels .......................................................................................................................................................................... 61

SFP+ Modules Tested for use with ERA............................................................................................................................................................. 62

Install SFP+ Modules in the OPT Cards ......................................................................................................................................................62

Cabling OPT Cards to Connect a WIN a Switching CAN..................................................................................................................................... 64

Cabling OPT Cards to Connect the TEN to a Classic CAN .................................................................................................................................. 66

Cabling OPT Cards to Connect a TEN to a Switching CAN................................................................................................................................. 68

Cabling OPT Cards for Connecting to a Fiber AP............................................................................................................................................... 70

Connect the CAT Cards ..............................................................................................................................................................................71

Connect the AUT Cards..............................................................................................................................................................................73

Connect the CDD Cards..............................................................................................................................................................................75

Calculate the Power Draw................................................................................................................................................................................. 75

Connect the CDD Card to the BBU .................................................................................................................................................................... 75

Maintenance ........................................................................................................................................................................................... 78

WCS Subrack Filter Module Maintenance......................................................................................................................................................78

Removing a WCS Subrack Filter Module....................................................................................................................................................78

Cleaning a WCS Subrack Filter Module......................................................................................................................................................79

Installing a WCS Subrack Filter Module .....................................................................................................................................................79

Removing an e-POI Module from an e-POI Subrack....................................................................................................................................... 80

Cat6A Specifications and Testing Requirements....................................................................................................................................... 81
Contacting CommScope........................................................................................................................................................................... 82

CMS Global Technical Support ....................................................................................................................................................................... 82

Telephone Helplines ..................................................................................................................................................................................82

Online Support...........................................................................................................................................................................................82

Waste Electrical and Electronic Equipment Recycling....................................................................................................................................82

Hardware to Software Mapping Information.................................................................................................................................................83

Technical Training...........................................................................................................................................................................................83

Accessing ERA Series User Documentation ....................................................................................................................................................83

Содержание e-POI























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды