36
Acquiring an RFID key code from the keypad
1. From the keypad, enter a valid installer code (default master code 001961).
2. Press
Prog
3. The
fi
rst and second lines of the display will show the messages “Main Menu” and “Parameter Prog.” respectively, indicating that you can now
modify the system options
4. Press the Con
fi
rm key to enter the respective submenus
5. Using the navigation keys (up and down) select “ProximityKeys” submenu. Press Con
fi
rm
6. The display will show the message “Key 1” and below it, the parameter that you can modify, namely “Description”
7. Using the navigation keys (left and right), select the number of the key you intend to acquire.
8. Press Con
fi
rm if you intend to change the description, then con
fi
rm to make the change or press C to leave the description as it is
9. Using the navigation keys (up and down), select the "Acquire" submenu. Still using the navigation keys, select the type of peripheral from
which you intend to acquire the key code and its bus address, then press Con
fi
rm again
10. The display will show the message “Acq. Key: In progress...”
11. Bring the key close to the RFID reader: the message will change from "In progress..." to "Acquired"
12. Press Con
fi
rm: the display will show a description of the colour of the key's plastic housing
13. Press Con
fi
rm again to associate the key to the desired user.
14. Once you have
fi
nished making changes from the keypad, remember to transfer them to the PC by means of the Comelit alarm switchboards
con
fi
guration programme.
Changing the date and time
√
To change the date and time from the keypad, you need to go into programming mode.
1. Go into programming mode as an installer (see relevant paragraph).
2. Using the navigation keys, select “System Mgmt.”, then continue as a user.
As installer:
1. Go into programming mode as a user (see relevant paragraph).
2. Using the navigation keys (up and down), select the “Options” menu on the second line of the display, and press Con
fi
rm.
3. Using the navigation keys (up and down), select the “Change date/time” option on the second line, and press Con
fi
rm.
4. The
fi
rst line will show DD-MM-YY (day, month and year) and the second line will display the date set on the switchboard.
5. Enter the date using the number keys (e.g. 1 September 2012 becomes 010912), then con
fi
rm.
6. The
fi
rst line of the display now shows HH-MM (hours and minutes) and the second line shows the time set on the switchboard.
7. Enter the time in the format displayed (e.g. 1.15 pm becomes 1315), then con
fi
rm.
8. This done, the display will show the message PARAMETER CHANGED.
9. Press C to go up one level in the menu, or C repeatedly until the date and time appear on the keypad.
As user:
Acquiring a radio sensor code from the keypad
1. Insert the battery in the sensor concerned and wait until the LED stops
fl
ashing. This applies to both magnetic contacts (REED) and infrared detectors
(PIR)
2. From the keypad, enter a valid installer code (default master code 001961).
3. Press
Prog
4. The
fi
rst and second lines of the display will show the messages “Main Menu” and “Parameter Prog.” respectively, indicating that you can now modify
the system options
5. Press the Con
fi
rm key to enter the respective submenus
6. Using the navigation keys (up and down), select “Radio Zones” submenu. Press Con
fi
rm
7. The display will show the message “Radio Zone 1” and below it, the parameter that you can modify, namely “Description”
8. Using the navigation keys (left and right), select the position in which you intend to acquire the sensor
9. Using the navigation keys (up and down), select “Acquisition” and press Con
fi
rm The display will show the message “Acq. Radio Zone: In progress...”
10. Now press and release the tamper button on the sensor
11. If acquisition is successful, the display will show the type of sensor (REED or PIR) and the unique code number of the sensor.
12. If acquisition fails because the sensor is already saved on the switchboard, the display will show the message “Acq. failed Dev. Duplicated” In this
case, it is preferable to acquire the parameters from a PC using the con
fi
guration software, in order to check the programmed sensors, the acquired
codes and their parameters. This will make it easier to correct any con
fi
guration errors.
13. Once you have
fi
nished making changes from the keypad, remember to transfer them to the PC by means of the Comelit alarm switchboards
con
fi
guration programme.
