35
Setting the serial number of the keypad
At
fi
rst start-up, the keypad displays the message NOT CONNECTED. To enable the switchboard to recognise keypad number 1 (the only
keypad that can be recognised by the switchboard by default), proceed as follows:
1. Press the prog key on the keypad: the display will show the message 1 Con
fi
g. Bus followed by two vertical arrows (up and down).
2. Press the con
fi
rm key located immediately below the navigation keys
3. Enter the serial number of the
fi
rst keypad by typing the digits 001 in sequence, and then press con
fi
rm
4. The display now shows the message SERIAL COM. Speed: with the proposal 38400.
5. Press con
fi
rm.
Keypad number one will now be taken in charge by the switchboard and can be used for activating, deactivating and con
fi
guring the system.
Activating and deactivating the system
To activate the alarm system completely, proceed as follows
:
1. From the keypad, enter a valid user code (the default setting is 111111) and then press the ON key
2. The keypad asks for con
fi
rmation: “TOTAL ACTIVATION?”
3. Press the Con
fi
rm key to con
fi
rm.
4. The keypad con
fi
rms the action with the message: “ACTIVATED”
To activate the system partially or to run a scenario, proceed as follows
:
1. From the keypad, enter a valid user code (default 111111) followed by either the Partial 1 key or the Partial 2 key.
2. If necessary, use the up and down navigation keys to select a different scenario from the proposed scenario, and then press Con
fi
rm.
3. The keypad con
fi
rms the action with the message: “ACTIVATED”
To deactivate the alarm system completely, proceed as follows
:
1. From the keypad, enter a valid user code (the default setting is 111111) and then press the OFF key.
2. The keypad con
fi
rms the action with the message: “DEACTIVATED”
3. Deactivation will also deactivate any alarms in progress within a few seconds.
Muting an alarm with the system deactivated
To mute an alarm with the system deactivated, proceed as follows:
1. From the keypad, enter a valid user code (default 111111).
2. Once the code has been recognised, press the Prog key until the message “DONE” appears on the screen.
3. This will mute the alarm.
Going into programming mode as a User
To go into programming mode as a user, proceed as follows:
1. From the keypad, enter a valid user code (default 111111)
2. Press
Prog
3. The
fi
rst line of the display will show the message “System Mgmt.” indicating that you can now modify the system options
Going into programming mode as an Installer (installer code authorisation)
The installer code must be authorised by the user, so the procedure is as follows:
1. Go into programming mode as a user (see previous paragraph)
2. Using the navigation keys (up and down), select the “COMMANDS” menu on the second line of the display, and press Con
fi
rm: the message
“GENERATE COMMAND” will appear on the
fi
rst line of the display
3. Using the navigation keys (up and down), select “AUTH. INSTALLER?” on the second line, and press Con
fi
rm: the message “DONE” will
appear on the display
4. Press C until you have exited the menus completely (i.e. until the date and time are displayed on the keypad)
5. From the keypad, enter a valid installer code (default master code 001961).
6. Press Prog
7. The
fi
rst and second lines of the display will show the messages “Main Menu” and “Parameter Mgmt.” indicating that you can now display or
modify the system options
8. From this position, you can use the navigation keys to select either the “System Mgmt.” menu, which corresponds to the user menu, or the
“Parameter Prog.” menu, which is reserved for the installer
9. Press the Con
fi
rm key to enter the respective submenus
