8
www.combisteel.com
Operation Instruction
1.
Select the proper size vacuum pouch. Allow a minimum of 1” to 2” of extra headspace at the top of the pouch to
ensure quality, air-tight seal
2.
Let the machine plug into a safety grounding socket, turn the Power Switch to ON step and the machine displays
CLO.
3.
Open the lid, then the machine will display ON, and it will stay at the READY status. Put the vacuum pouch into the
chamber and make sure the bag opening is across the seal wire and well fixed.
4.
Press the Setting button and the
∨
and
∧
button to set the time of each mode. Timing range of vacuum: 5-90s;
Timing range of gas inflation: 0-10; Timing range of sealing: 0-6s; Timing range of cooling 0-10s. When finish all the
settings, press the Setting button again, the machine will be back to the ready mode and shows ON. (If one setting
is adjusted the time to 0, it means that this process will be removed during operation.)
5.
Close the lid, then the machine starts working. The indicate light of the working process will be on accordingly, and
the machine will show the rest time of that working mode.
6.
After the operation finishes, the lid will release automatically, and the machine will give out a beep sound.
7.
Take out the pouch and go on with next process that you want.
(Vacuum package can only slow the process of food spoilage, but it cannot stop food spoilage. With vacuum package,
the food still needs to be freezing in fridge.
8.
Restore Factory Defaults
Let the machine power on. When the machine shows OFF, press SET button and
“∧”
button at the same time
for 3s. When the machine gives out a beep sound and shows rS, then it is successful to restore factory defaults.
Maintenance
In order to prolong the service life of machine, avoid any quality failure and meet the best packing performance, maintenance
is a must to the machine. If the machine is used frequently (working more than 4hours per day), then it is suggested being
implemented with a professional maintenance every six months. If it is used less than 4 hours per day, then it is ok to be
implemented a completed maintenance every year (it depends on the working condition and product self-condition).
•
Before maintaining, please unplug the power cord of machine from socket.
•
If the machine doesn’t work normally and give out some strange noise, please turn it off and contact the supplier.
•
Don’t use the detergent (containing solvent) to clean the machine. At least check the lid if broken or not per week. If the
lid is broken, please stop using the machine immediately.
•
Never treat the machine in high pressure cleaning, as it will severely damage the electrical parts or other parts of the
machine.
•
Never let any water enter the vacuum port in chamber or air outlet hole of pump, otherwise it will cause the irreparable
damages on pump.
•
Non-specialist could not carry on a large-scale maintenance to the machine.
•
Keep the machine at an upright position when move or transit it as tipping it over will damage the pump
•
The machine could work 8 hours at most per day. If users prolong the working time of machine without authorization
and cause any damage or quality issue on the machine, supplier won’t take any responsibility for that.
•
If user doesn’t operate the machine according to this manual and cause any damage or quality issue on machine, factory
won’t take any responsibility for that.
Lid
•
Never place the machine nearby the heat source in case of damaging the lid.
•
Never put anything that is heat/sharp/heavy on the lid, otherwise it might damage the lid.
•
Please use the solvent-free detergent to clean the lid, as the solvent might damage the lid.
•
At least check if the lid is broken or not per week. If the lid is broken, please stop using the machine immediately until a
new lid is replaced. Keep using a broken lid might cause the lid inside explosion. If any explosion from the lid, it will cause
accidence on human. For this kind of wrong operation, supplier won’t take any responsibility.
•
For safety, please replace the lid every 3 years.
Pump
In order to prolong the service life and make sure the correct operation, it is very important to carry on a daily maintenance
to the pump. If the machine is used frequently, we suggest that at least a fully checking per year need to be implemented on
pump. If any doubt or advise, please contact the supplier.
•
A new machine doesn’t have the oil in pump. If use a new machine at the 1st time, please fill the oil before use.
•
Please check the colour of oil.
•
The oil should be clear and bright, could not be muddy and contain bubble. When the oil is at rest, but some white stuffs
in oil still doesn’t disappear, it means that the oil contains some impurities. If the oil contains impurities or becomes
black, the oil must need changing.
•
The service life of oil
