Colorjet VerveLED VLR 2513 Скачать руководство пользователя страница 9

Страница: 9 / 49

Page | 8

Verve LED

7. Unpacking and Unloading the Printer Box

Machine and Tool Requirements

The

Machine and Tool Requirements

are shown as follow:

▪

Fork lift

▪

Crane

▪

Heavy duty lifting belt/sling

▪

Powered screw/nut driver

▪

Nut driver

▪

Spanner

Unloading the Machine

The net weight of the machine is 1762 Kgs. After packing, the weight gets increased up to 1962 Kgs
approximately.

Follow these steps to unload the machine:

Step 1:

Tied the machine using ropes/slings for making a perfect balance for lifting.

Step 2:

Unload the machine from the container or lorry.

Step 3:

Machine should be kept on leveled and cleaned surface or floor.

Now, the machine gets unloaded.

Unpacking the Machine

Note:

Packing may vary country to country.

Follow these steps to unpack the machine for wooden packing (Export):

Step 1

: Remove the 5x38 mm screws from all the wooden plank side walls using the Nut Driver of 8mm

Bit.

Step 2:

Gently remove the wooden top cover of the printer box including side walls.

Step 3:

Carry out Chiller Unit and accessories box.

Step 4:

Unpack the printer cover (bubble wrap).

Step 5:

Lift the machine using Fork Lift and place it on an even place.

Содержание VerveLED VLR 2513


















































Результаты поиска

Содержание VerveLED VLR 2513

Отзывы:

Похожие инструкции для VerveLED VLR 2513

Бренды по названию

Популярные бренды

Colorjet VerveLED VLR 2513, Инструкция по установке и устранению неисправностей

Результаты поиска

Содержание VerveLED VLR 2513

Отзывы:

Похожие инструкции для VerveLED VLR 2513

Бренды по названию

Популярные бренды