background image

 

Page | 6  

 

Verve LED 

 3. Safety Precautions 

Before  operating  the  printer  and  Print  Control  Centre  software  for  the  first  time,  please  read  the 
document  carefully  and  follow  all the  usage  instructions. While  using  the  printer, kindly  follow  all  the 
safety instructions which are given below:   

Fire Prevention 

Inks  and  solvents  must  be  enclosed  in  a  special  storage  cabinet  for  inflammable  liquids  or  within  a 
separate storage room and must be clearly identified to meet the professional requirements of safety 
regulations. Ink storage must be strictly in compliance with local fire regulations for the use and storage 
of combustibles. 

Ventilation 

In order to prevent the danger caused by volatile gas accumulation, the storage room must have sufficient 
ventilation.  

Note

: Solvent gas specific gravity is greater than the air, it would accumulate near the floor. Installation 

work in the vicinity of electrical equipment must confirm the GB/T standards, national electrical regulation 
requirements  for  level  II  sites,  and  installation  by  a  corresponding  qualification  of  the  professional 
electrical contractor.  

 

 

4. Electric Requirements 

Before installing the printer, the below mentioned electrical requirements should be confirmed: 

 

Total Power Consumption is 7KW. 

 

Machine needs single phase AC 220V, 30Amps (+ / - 10%), 50/60Hz.   

 

Uninterrupted power supplies (flicker free) should be provided as it has digital circuit. 

 

Exclusive Earthing should be required for printer and it should not be shared with UPS and Building's 
common Earth. 

 

 

Printer and computer must share same exclusive earthing.

 

 

Proper Earth Connection

 

The trouble-free printing depends on the earth connection provided to the machine. In some cases, the 
media  generates  static  and  excessive  charges  that  can  damage  the  Print  Head  as  well  as  affect  the 
placement  of  printing  dots.  Thus,  one  should  provide  the  proper  earth  connection  before  using  the 
printer.  

Precautions: 

 

A separate earth connection should be provided to the machine 

 

The earth resistance should be in the range of 4-5 ohms 

Note

: Ensure that the earth point for the Printer and PC should be same for the safety of interfaces. 

Содержание VerveLED VLR 2513


















































Отзывы: