Cole Parmer 77111-00 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 40

background image

B/T

®

RAPID-LOAD

®

Peristaltic Pumps and Drive Operating Manual 2-3

Cole-Parmer

Section 2

Installation and Setup

This unit should be placed on a flat surface such as a floor, bench, or table
and should be near a compressed air source.

Unpack the drive and save packaging material until proper product
operation has been verified.

Install the following components: pressure gauge, pressure filter/regulator
and lubricator assembly, pipe nipple, elbow, and muffler. See Figure 2-5 for
proper orientation, (all items and fittings included except as noted). Use a
thread seal such as PTFE tape for all connections to reduce the possibility
of air leakage.

Connect compressed air line to the 1/4 NPT connection on the regulator
(fitting not supplied). Turn on compressed air line to start pumping.
(Maximum 100 psig inlet.)

NOTE:

Pump will not run unless Door Assembly is closed.

Model 77111-80

Figure 2-5.

Air-Powered Rapid-Load Pump and Drive

Filter/Regulator
Control Knob
(Speed Control)

Muffler

Lubricator
Control Knob

Door
Assembly

Gear Reducer

Elbow

Pipe Nipple

Pressure Gauge

Base

Air Motor

«
...
9
10
11
12
13
...
»

Содержание 77111-00









































Отзывы:

Нет отзывов

Похожие инструкции для 77111-00

Бренд: SAB Страницы: 7

Бренд: Underhill Страницы: 2

Бренд: Quincy Compressor Страницы: 122

Бренд: York Страницы: 84

Бренд: Dux Страницы: 20

PacificHydrostar 2" Gasoline Powered Clear Water...

Бренд: Pacific hydrostar Страницы: 24

Бренд: Cordivari Страницы: 44

Бренд: Tiger Страницы: 36

Бренд: CLIVET Страницы: 7

Бренд: Baker Hughes Страницы: 78

Бренд: Pattfield Ergo Tools Страницы: 162

Бренд: Echelon Страницы: 8

Бренд: salmson Страницы: 16

Бренд: Oilon Страницы: 68

LARIUS SIRIO 60:1

Бренд: Samoa Страницы: 46

DSE-5 THRU DSE-120

Бренд: A.O. Smith Страницы: 24

Бренд: clage Страницы: 148

Бренд: Barnes Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды