Cole Parmer 77111-00 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 40

background image

4-2

B/T

®

RAPID-LOAD

®

Peristaltic Pumps and Drive Operating Manual

Cole-Parmer

Section 4

Maintenance and Troubleshooting

REPLACING ROLLERS

To replace rollers:

1. Using a retaining ring tool (Part Number 109852-CR), remove the

retaining rings from the ends of the roller axles and slide the rollers off.
Take care to avoid opening the retaining rings too wide.

2. Check to be sure that the wave washers are installed on the axles

against the rotor plate.

3. Slide the new rollers, Replacement Roller Kit 07584-02, onto the axles,

placing the ends with the flush bearing surface inward toward the rotor
plate against the wave washers, and the etched ends with the recessed
bearing surface outward toward the free ends of the roller axles.

4. Replace the retaining rings. You may have to push the rollers in to

compress the wave washers to allow the retaining rings to engage the
grooves in the axles.

Figure 4-2.

Exploded Roller Sub-Assembly

«
...
26
27
28
29
30
...
»

Содержание 77111-00









































Отзывы:

Нет отзывов

Похожие инструкции для 77111-00

DRAZICE TO - 20.1

Бренд: Nibe Страницы: 13

Pond Clear 5000

Бренд: SuperFish Страницы: 12

Бренд: salmson Страницы: 68

DynaDrive DD60-10

Бренд: Davey Страницы: 32

Бренд: ThermoFlow Страницы: 34

MiniTank WM-1.0

Бренд: Waiwela Страницы: 20

Бренд: Utilitech Страницы: 40

Бренд: ICP Страницы: 16

CronoBloc BL Series

Бренд: Wilo Страницы: 43

Бренд: ubbink Страницы: 30

Бренд: E-gas Страницы: 10

PACIFIC HYDROSTAR 1/3 HP Submersible Sump Pump with Vertical Float...

Бренд: Pacific hydrostar Страницы: 9

Бренд: Cornelius Страницы: 19

AquaSurge PRO 2000-4000

Бренд: Aquascape Pro Страницы: 8

Бренд: York Страницы: 12

Бренд: Santon Страницы: 20

Бренд: Danfoss Страницы: 44

Бренд: American Water Heater Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды