Cole Parmer 77111-00 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 40

background image

B/T

®

RAPID-LOAD

®

Peristaltic Pumps and Drive Operating Manual 2-5

Cole-Parmer

Section 2

Installation and Setup

Install customer-supplied motors in accordance with the following procedure.

CAUTION: This product is intended for use with a motor that has
a maximum speed of 1800 rpm, @ 0.5 HP (0.67 KW). Do not use a
motor with a higher speed capacity.

WARNING: Electrical connections and grounding (earthing), must
conform to local codes. (See motor wiring diagram for motor
wiring instructions.)

Tools required: 13 mm Wrench.

Model 77111-55 is designed to be installed to a customer-supplied
IEC-72-71-14F130 frame motor with foot mountings. To install the
unit, refer to Figure 2-7 and follow these steps:

1. Using a 13 mm wrench, and the supplied hardware, bolt the motor to

the gear reducer by installing the four flat washers on the bolts and
inserting the bolts through the gear head adapter into the motor. Torque
bolts from 1.73 to 2.00 kilogram-meters (12.5 to 14.5 foot pounds.)

2. Cutoff connector from end of interlock cable and strip outer jacket.

3. Strip individual conductors and wire in series with the power to the

motor turned off. Failure to do so will result in defeating the door
interlock, creating a potential crushing hazard.

CAUTION: Risk of crushing. Keep fingers away from rotor while pump is
in operation. Stop pump before loading or unloading tubing.

Figure 2-7.

Motor Mounting IEC-72 71-14F130 Motor Frame

MODEL 77111-55

Trim Interlock Cable to
Length and

S

trip Leads.

Install in

S

eries with

Power to the Motor.

Gear Reducer

Pump
Head

Flat

W

ashers

and Bolts

«
...
11
12
13
14
15
...
»

Содержание 77111-00









































Отзывы:

Нет отзывов

Похожие инструкции для 77111-00

Бренд: Water Worker Страницы: 24

Бренд: Q-Pumps Страницы: 44

Бренд: ubbink Страницы: 29

Бренд: YANGTECH Страницы: 23

Бренд: UGSI Страницы: 125

Бренд: WaterLogic Страницы: 29

Бренд: Balcrank Страницы: 18

Бренд: Zenit Страницы: 136

Бренд: Raymarine Страницы: 24

SunCentric Series

Бренд: Dankoff Solar Страницы: 11

Бренд: Dux Страницы: 20

Бренд: Daikin Страницы: 26

Бренд: Liberty Pumps Страницы: 16

Бренд: OEG Страницы: 28

AQUAPRO AP1000FP

Бренд: Aquatec Страницы: 2

Бренд: Watts Страницы: 22

Бренд: Graco Страницы: 32

Smartmax Series

Бренд: ubbink Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды