8.3 Synchronising multiple ColourCyc 250 LXs without DMX 512 signal
The output of multiple
ColourCyc 250 LX
units may be synchronised without using an incoming DMX 512 signal, by utilising the
fixture’s synchronising signal and internally stored programs.
Multiple
ColourCyc 250 LX
fixtures may be utilised, operating in sequence and controlled by a MASTER fixture controlling multi-
ple SLAVE units.
Determine which of the
ColourCyc 250 LX
will act as master, usually by the criterion of ease of access:
Connect the XLR3 output of the master unit to the XLR input of the first slave unit. The XLR output of the first slave is then connec-
ted to the XLR input of the second slave, and so on up to a maximum total of 32 projectors.
If connecting more than 10 units, we recommend the us of a suitable opto-isolated connecting unit to amplify the signal as requi-
red.
Pin connections conform to the international standard:
pin 1= gnd
pin 2= data –
pin 3= data +
Ensure that all data conductors are isolated from one another and the
metal housing of the connector.
Note:
the housing of the cannon XLR must not be connected
under any circumstances.
Pin number 1 must be disconnected from the electrical con-
nection of the unit.
master
slave
out
made in italy by
coemar
spa
Castel Goffredo (mn)
factor
y
set main at:
100V
115V
208V
230V
240V
50Hz
60Hz
DMX OUT
DMX IN
5AT @230V
8AT @115V
POWER
fan
alert
lamp
status
DMX
test fan ON
lamp ON
DR1 remote
motor
calibration
shutter/strobe
inhibit
OFF - DMX addressing, ID personality
ON - built in program control
ON
ON
reset
1
2
4
8
16
32
64
128
256
PR 1
PR 2
PR 3
PR 4
SP 1
SP 2
SP 3
SP4
all PR
DMX addresses, ID personality or built in program and speed
all OFF for slave
serial number
230v
ie max: 2A
ie: 1,6A
115v
ie max: 4,2A
ie: 3,2A
max temp
ext:
150
°
C
ta max:
40
°
C
cos
ϕ
:
0,9
IP 20
weight:
18,4 kg
alto/top
2 m
2 m
dip-switches
Warning!
High voltage inside. Caution: hot lamp. Disconnect from power supply before
opening. A good ground connection is essential. Case is very hot. Do not install on
flammable surfaces. Min. Distance from flammable materials to all exterior surfaces:
0,5m. Important safety information, see instruction manual before use.
out
made in italy by
coemar
spa
Castel Goffredo (mn)
factor
y
set main at:
100V
115V
208V
230V
240V
50Hz
60Hz
DMX OUT
DMX IN
5AT @230V
8AT @115V
POWER
fan
alert
lamp
status
DMX
test fan ON
lamp ON
DR1 remote
motor
calibration
shutter/strobe
inhibit
OFF - DMX addressing, ID personality
ON - built in program control
ON
ON
reset
1
2
4
8
16
32
64
128
256
PR 1
PR 2
PR 3
PR 4
SP 1
SP 2
SP 3
SP4
all PR
DMX addresses, ID personality or built in program and speed
all OFF for slave
serial number
230v
ie max: 2A
ie: 1,6A
115v
ie max: 4,2A
ie: 3,2A
max temp
ext:
150
°
C
ta max:
40
°
C
cos
ϕ
:
0,9
IP 20
weight:
18,4 kg
alto/top
2 m
2 m
dip-switches
Warning!
High voltage inside. Caution: hot lamp. Disconnect from power supply before
opening. A good ground connection is essential. Case is very hot. Do not install on
flammable surfaces. Min. Distance from flammable materials to all exterior surfaces:
0,5m. Important safety information, see instruction manual before use.
in
Ad altri
ColorC
yc
250 LX
(slave)
Connect to other
ColorC
yc
250 LX
(slave)
9
English
