Cobalt Digital Inc 9902-DC-4K Скачать руководство пользователя | Manualshive

Страница: 20 / 62

background image

2

Installing the 9902-DC-4K Into a Frame Slot

2-2

9902-DC-4K PRODUCT MANUAL

9902DC4K-OM (V1.5)

Note:

Check the packaging in which the 9902-DC-4K was shipped for any extra
items such as a Rear I/O Module connection label. In some cases, this label
is shipped with the card and to be installed on the Rear I/O connector bank
corresponding to the slot location of the card.

Install the 9902-DC-4K into a frame slot as follows:

1.

Determine the slot in which the 9902-DC-4K is to be installed.

2.

Open the frame front access panel.

3.

While holding the card by the card edges, align the card such that the
plastic ejector tab is on the bottom.

4.

Align the card with the top and bottom guides of the slot in which the
card is being installed.

5.

Gradually slide the card into the slot. When resistance is noticed, gently
continue pushing the card until its rear printed circuit edge terminals
engage fully into the rear I/O module mating connector.

CAUTION

If card resists fully engaging in rear I/O module mating connector, check for
alignment and proper insertion in slot tracks. Damage to card and/or rear I/O
module may occur if improper card insertion is attempted.

6.

Verify that the card is fully engaged in rear I/O module mating
connector.

7.

Close the frame front access panel.

8.

Connect the input and output cables as shown in 9902-DC-4K Rear I/O
Modules (p. 2-4).

9.

Repeat steps 1 through 8 for other 9902-DC-4K cards.

Note:

• The 9902-DC-4K BNC inputs are internally 75-ohm terminated. It is not

necessary to terminate unused BNC inputs or outputs.

• External frame sync reference signals are received by the card over a

reference bus on the card frame, and not on any card rear I/O module
connectors. The frame has BNC connectors labeled REF 1 and REF 2
which receive the reference signal from an external source such as a house
distribution.

• To remove a card, press down on the ejector tab to unseat the card from the

rear I/O module mating connector. Evenly draw the card from its slot.

10.

If network remote control is to be used for the frame and the frame has
not yet been set up for remote control, perform setup in accordance with
Setting Up 9902-DC-4K Network Remote Control (p. 2-5).

Note:

If installing a card in a frame already equipped for, and connected to
DashBoard™, no network setup is required for the card. The card will be dis-
covered by DashBoard™ and be ready for use.

«
...
18
19
20
21
22
...
»

Содержание 9902-DC-4K































































Отзывы:

Нет отзывов

Похожие инструкции для 9902-DC-4K

Бренд: Uebo Страницы: 2

Бренд: X-Micro Страницы: 23

Бренд: Naxa Страницы: 36

Varispeed-606PC3

Бренд: YASKAWA Страницы: 157

FL MC 10BASE-T/FO G850

Бренд: Phoenix Contact Страницы: 7

Бренд: DAISHIN Страницы: 28

Бренд: argon audio Страницы: 6

Бренд: B&B Electronics Страницы: 2

Бренд: Avtech Страницы: 4

Бренд: MyGica Страницы: 28

Бренд: RDZ Страницы: 60

Бренд: EVOLV Страницы: 12

Бренд: RuarkAudio Страницы: 56

Бренд: Metrodata Страницы: 17

Бренд: PhD Solutions Страницы: 14

ControlVIT CV10 series

Бренд: Salicru Страницы: 5

Бренд: Ledco Страницы: 4

WHISPER 30 ULTRA

Бренд: Mastervolt Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды